ROHN H30 30' foot Telescoping Mast Outdoor Antenna Pole
Made in the USA!
ROHN H30, 3 section Mast extends to about 27 Feet in height that ships to Commercial and Residential addresses alike. Used for Off-Air TV Antenna, Amateur (Ham) Radio, Wireless Internet Antenna, MMDS and Cell Phone Signal Booster Installations (not included).
Manufacturers recommend that masts heights of 10 feet and higher above the uppermost bracket be guyed for Addition Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance
(Antenna, Down Guys and Mounts not included).
This Item Ships LTL Freight ONLY.

ROHN H20 20' foot Telescoping Mast Outdoor Antenna Pole
Made in the USA!
The ROHN H20, 2 section Telescopic Mast extends to about 19 Feet in height that ships to Commercial and Residential addresses alike. Used for Off-Air TV Antenna, Amateur (Ham) Radio, Wireless Internet Antenna, MMDS and Cell Phone Signal Booster Installations (not included).
Manufacturers recommend that masts heights of 10 feet and higher above the uppermost bracket be guyed for Addition Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance
(Antenna, Down Guys and Mounts not included).
This Item Ships LTL Freight ONLY.

ROHN H20 H Kit Replacement Hardware Kit for H20 Telescopic Antenna Mast
Made in the USA!
This ROHN OEM Factory H20 Telescopic Mast Hardware includes: Cotter Pins, Guy Rings and Mast Clamps with Bolt Assemblies. Basically everything but the Mast Tubes themselves (not included).

ROHN H30 H Kit Replacement Hardware Kit for H30 Telescopic Antenna Mast
Made in the USA!
This ROHN OEM Factory H30 Telescopic Mast Hardware includes: Cotter Pins, Guy Rings and Mast Clamps with Bolt Assemblies. Basically everything but the Mast Tubes themselves (not included).

ROHN H40 H Kit Replacement Hardware Kit for H40 Telescopic Antenna Mast
Made in the USA!
This ROHN OEM Factory H40 Telescopic Mast Hardware includes: Cotter Pins, Guy Rings and Mast Clamps with Bolt Assemblies. Basically everything but the Mast Tubes themselves (not included).

ROHN H50 H Kit Replacement Hardware Kit for H50 Telescopic Antenna Mast
Made in the USA!
This ROHN OEM Factory H50 Telescopic Mast Hardware includes: Cotter Pins, Guy Rings and Mast Clamps with Bolt Assemblies. Basically everything but the Mast Tubes themselves (not included).

ROHN GR1 Guy Ring for 1-1/4" Telescopic and Antenna Mast Placement
Made in the USA!
This is a ROHN OEM Factory GR1 Telescopic Mast Rolled Edge Guy Ring with a 1-1/4" ID. There are two of these used on every ROHN H-Series Telescopic Antenna Mast. The innermost tube section is always a 1-1/4 inch OD 16 AWG mast where these 1-1/4 inch ID rings are placed at both the Top and Bottom of this section with the bottom resting on the next innermost Mast Tube Section. These two are the most likely to wear out due to the load forces exerted upon them.
(1) Ring Per Order.

ROHN H40 40 foot Outdoor Antenna Telescopic Mast Pole
Made in the USA!
ROHN H40, 4 section Mast extends to about 35 Feet in height that ships to Commercial and Residential addresses alike. Used for Off-Air TV Antenna, Amateur (Ham) Radio, Wireless Internet Antenna, MMDS and Cell Phone Signal Booster Installations (not included).
Manufacturers recommend that masts heights of 10 feet and higher above the uppermost bracket be guyed for Addition Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance
(Antenna, Down Guys and Mounts not included).
This Item Ships LTL Freight ONLY.

ROHN H50 50 foot Outdoor Antenna Telescopic Mast Pole
Made in the USA!
ROHN H50, 5 section Mast extends to about 43 Feet in height that ships to Commercial and Residential addresses alike. Used for Off-Air TV Antenna, Amateur (Ham) Radio, Wireless Internet Antenna, MMDS and Cell Phone Signal Booster Installations (not included).
Manufacturers recommend that masts heights of 10 feet and higher above the uppermost bracket be guyed for Addition Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance
(Antenna, Down Guys and Mounts not included).
This Item Ships LTL Freight ONLY.