ROHN TB3 2" inch Heavy Duty Thrust Bearing for 25G 45G 55G Series Towers
Made in the USA!
The ROHN TB3 Thrust Bearing is pre-drilled to mount onto ROHN G-Series Tower Top Cap Sections and Plates like the 25AG4, BPL25G, BAS25G, 45AG4, BPL45G and BPL55G that are in turn, pre-drilled to accept the TB3 in support of up to 2.00" OD Mast. The TB3 is not intended to be mounted onto AS25G or AS455G Accessory shelves. The Rotor can then be Mounted on these Accessory Shelves Below.

ROHN TB4 3" inch Heavy Duty Thrust Bearing for 25G 45G 55G Series Towers
Made in the USA!
The ROHN TB4 Thrust Bearing is pre-drilled to mount onto ROHN G-Series Tower Top Cap Sections and Plates like the 25AG4, BPL25G, BAS25G, 45AG4, BPL45G and BPL55G that are in turn, pre-drilled to accept the TB4 in support of up to 3.00" OD Mast. The TB4 is not intended to be mounted onto AS25G or AS455G Accessory shelves. The Rotor can then be Mounted on these Accessory Shelves Below.

ROHN ACL455 Anti-Climb Panels Safety Accessory for 45G 55G Tower Section
Made in the USA!
These ROHN ACL455 Anti-Climb Panel Kit consists of (3) Panels with associated Hardware are Installed for Protection and Public Safety on each Face of the Bottom 45G or 55G Tower Section. Search for the ACL models for the other ROHN Tower Series. Together with ACWS Anti-Climb Warning Sign and appropriate fencing, these panels help protect your Tower from Unauthorized Climbing Activities
This Item Ships LTL Freight ONLY!

ROHN BPL55G Thrust Bearing Plate and Down Guy Top Cap for 55G Tower
Made in the USA!
The ROHN BPL55G Thrust Bearing Top Cap Plate bolts onto the top of any Standard ROHN 55G Main Tower section and can provide extra clearance for installation of equipment such as Rotors on an Accessory Shelf mounted on a section below. The BPL55G is pre-drilled to accept mounting for the ROHN Thrust Bearing TB3 (2" ID) or TB4 (3" ID) and also provides Down Guy Attachment to this very same plate via Shackles and Thimbles.(Not Included)

ROHN SR55 Safety Ring Attachment for 55G Tower Service and Installation Work
Made in the USA!
The SR55 Snaps into place at any level with No bolts required. This attachment fits the ROHN 55G Tower Series and Compliments the Work Platform Accessory (WP55G for 55G, Not included). These Accessories, along with your safety harness, provides a Safe Work Space Environment at any Tower Height.

ROHN WP55G Work Platform Attachment for 55G Tower Service & Installation Work
Made in the USA!
The ROHN WP55G Snaps into place at any Tower level with No bolts required. This attachment fits the ROHN 55G Tower Series and Compliments the Safety Ring Accessory (SR55 Not included). These Accessories, along with your safety harness, provides a Safe Work Space Environment at any Tower Height.

ROHN TB55D Torque Bar Stabilizer Accessory for GA55GD Guy Bracket Assembly
Made in the USA!
This is (1) Bar per Order, needing (3) in total to complete a 3-way down guy configuration. This Accessory Modifies a New or Existing GA55GD Down Guy Bracket Assembly (Not included) into a Torque Stabilizer Assembly that would be installed at existing Guy attachments on any horizontal brace as opposed to tower section joints as provided for by the TA55 (Not included) Stabilizer Assembly which would require additional Down Guy Attachments. This Item will also require the purchase of 3/8" inch shackles to complete the upgrade.

ROHN KY2041A Waveguide Cable Hanger Bracket for 25G 45G 45GSR 55G 65G Tower
Made in the USA!
The ROHN KY2041A 3-hole Waveguide Cable Bracket is used to secure Waveguide Cable Lines to the legs of standard ROHN 25G 45G 45GSR 55G 65G tower sections. The hot-dip galvanized brackets feature (3) 7/16 and (3) 3/4 holes and can be mounted to Tower Section Rail Legs from 3/4 - 2 1/4" inch in Outside Diameter. It is recommended that (5) KY2041A be used per 20ft of tower for 4ft OC spacing.(1 per Quantity Ordered)

ROHN 3/4X12PP Pier Pin 3/4" x 12" inch installed for 25G 45G 55G Concrete Base Plates
Made in the USA!
The ROHN 3/4X12PP Pier Pin is a 3/4 inch DIA x 12 inch long Hot Dip Galvanized Steel Rod Section used to align the BPC25G BPC45G BPC55G Concrete Base Plates on top of a Concrete Pier to prevent lateral movement only.(Concrete Base Plate is a Separate Item) The ROHN 25G 45G 55G Guyed Towers are then erected Over Center of the Pier Pin held Concrete Base Plate. Without Torque Arm Supplemented Down Guys, the Tower may twist slightly as the guys merely keep the tower plumb and centered but do not prevent twist under load. A Short Base or Main Tower Section Embedded in a concrete pour foundation will reduce this affect tremendously and a Torque Arm Assembly installed in proximity to the location of the Antennas mounted on the tower will minimize it further.
A Concrete Base Plate cannot be used as a Self Supporting Base Plate (see 25GSSB 45GSSB 55GSSB).
This Pier Pin is also used with 25TG 45TG 55TG Tapered Base Sections.

ROHN BPC55G Concrete Base Plate for 55G Guyed Tower
Made in the USA!
The ROHN BPC55G uses a 3/4" x 12" pier pin to align the plate to the concrete slab and prevents Lateral Movement for ROHN 55G Guyed Tower installations only. This ROHN Base Plate allows the ROHN 55G Tower to be Mounted onto an existing or new Concrete Pier, Pad or Slab but Cannot be Used as a Self Supporting Base Plate.(none exists for the 55G, see R-SB55G)
All 55G Tower Installations should be temporarily Guyed during erection.

ROHN FR55G Flat Roof Mount Base for 55G Guyed Tower on Building
Made in the USA!
The ROHN FR55G bolts directly onto a Watertight and Reinforced Flat Roof Surface for a 55G Guyed Tower, but Cannot be Used as a Self Supporting Base Plate. (none exists for the 55G) Roof Mounted Tower Options may limit Potential Height considerably as there is no Wind Load vs. Height Guidance to be found this type of Mounting in any of the Specification Literature for good reason. You need to Consult an Engineer to determine the Load Bearing Capability and Wind Speed Survivability of such an Installation. Guying is an absolute must, but remember that guying will simply increase the down pressure onto the Base support, which in this case, is your Roof!

ROHN SB55G 5' foot Short Base Section for 55G Self-Supporting or Bracketed Tower
Made in the USA!
The ROHN SB55G is a 5 foot Short Base Section for Embedment in a poured Concrete Pad prior to erection of a 55G Bracketed or Self-Supporting Tower. This Short Base Section is set into a hole, with concrete poured around it and resting on top of gravel layer underneath to provide a Drained, Bolted and Fixed Connection to a 45G Main Tower or Top Cap Section which provide addition twist control.

ROHN APL1258UM Accessory Plate for Universal Mount of Beacon Light on Any Tower Leg
Made in the USA!
This ROHN APL1258UM Accessory Plate provides for Universal Mounting of Aviation Lighting, Beacons and other Equipment at Mid Level Height on the Round or Angled leg of Any ROHN Tower Series.

LRCL-5 5' Foot x 5/8" Copper Clad Lightning Rod for Tower Plates, Caps & Leg Mounts
The LRCL is a 5' Foot x 5/8" Copper Clad Lightning Rod ONLY that comes threaded, with Nut and Washer Hardware, for mounting onto Tower Top Assembly Plates (i.e. ROHN APL25G, APL45G, APL55G, APL4A, APL4HA), Leg Mounts and Caps (i.e. ROHN VW133, VW132, VY1949A, VY1949-A) as well as extraneous Mounts such as the Harger CUBU581 Air Terminal Base.
Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose.

LRCL-4 4' Foot x 5/8" Copper Clad Lightning Rod for Tower Plates, Caps & Leg Mounts
The LRCL-4 is a 4' Foot x 5/8" Copper Clad Lightning Rod ONLY that comes threaded, with Nut and Washer Hardware, for mounting onto Tower Top Assembly Plates (i.e. ROHN APL25G, APL45G, APL55G, APL4A, APL4HA), Leg Mounts and Caps (i.e. ROHN VW133, VW132, VY1949A, VY1949-A) as well as extraneous Mounts such as the Harger CUBU581 Air Terminal Base.
Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose.

LRCL-3 3' Foot x 5/8" Copper Clad Lightning Rod for Tower Plates, Caps & Leg Mounts
The LRCL-3 is a 3' Foot x 5/8" Copper Clad Lightning Rod ONLY that comes threaded, with Nut and Washer Hardware, for mounting onto Tower Top Assembly Plates (i.e. ROHN APL25G, APL45G, APL55G, APL4A, APL4HA), Leg Mounts and Caps (i.e. ROHN VW133, VW132, VY1949A, VY1949-A) as well as extraneous Mounts such as the Harger CUBU581 Air Terminal Base.
Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose.

LRCL-8 8' Foot x 5/8" Copper Clad Lightning Rod for Tower Plates, Caps & Leg Mounts
The LRCL-8 is a 8' Foot x 5/8" Copper Clad Lightning Rod ONLY that comes threaded, with Nut and Washer Hardware, for mounting onto Tower Top Assembly Plates (i.e. ROHN APL25G, APL45G, APL55G, APL4A, APL4HA), Leg Mounts and Caps (i.e. ROHN VW133, VW132, VY1949A, VY1949-A) as well as extraneous Mounts such as the Harger CUBU581 Air Terminal Base.
Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose.

ROHN TA55 Torque Arm Stabilizer Anti-Twist Down Guy Assembly for 55G Tower
Made in the USA!
This ROHN TA55 Torque Arm Anti-twist Stabilizer Down Guy Assembly is to be located in the area of the Microwave or other Focused Beam antennas to provide six-way guying. The Assembly Comes welded as (1) Piece and attaches to the Tower at any Section Joint using slightly longer Joint Bolts through each Rail as the Sections Join Together.(included)
MUST BE INSTALLED AS SECTIONS ARE JOINED TOGETHER.
You will Need (6) 5/8" Shackles with a thimble around each shackle to seat whichever size EHS Strand Big Grip Preform Dead-end to terminate the Down Guy. The Big Grips and Thimbles will depend on the size of the Guy wire to be used 3/16EHS,1/4EHS or 5/16" EHS Strand(See Spec Sheet for Illustration)

ROHN GA55GD Down Guy Bracket Assembly for 55G Guyed Tower Installation
Made in the USA!
The GA55GD Mounts to the ROHN 55G Series Guyed Towers at any Horizontal Brace. This Guy Assembly is used to attach guy wires to the ROHN 55G tower. It is recommended as an Attachment to a ROHN Tower Section for use at every guy level. The 55G tower can be used in guyed, self-supporting or bracketed configurations according to specifications in the ROHN catalog. Check the ROHN Tower Catalog for Specific Height Details.

ROHN TA553 Torque Arm Stabilizer Anti-Twist Down Guy Assembly for 55G Tower
Made in the USA!
This ROHN TA553 Torque Arm Anti-twist Stabilizer Down Guy Assembly is to be located in the area of the Microwave or other Focused Beam antennas to provide six-way guying. Comes in 3 Structural Pieces that joint together via Top & Bottom Plates where each piece meets another, being assembled around the Tower Section. The Assembly then attaches to each of the (3) Tower Leg Rails with U-clamps, preferably resting above the Tower Section Joint Sockets. Torque Arm Lugs are provided.
CAN BE INSTALLED AFTER SECTIONS ARE JOINED TOGETHER ON EXISTING TOWERS.
You will Need (6) 5/8" Shackles with a thimble around each shackle to seat whichever size EHS Strand Big Grip Preform Dead-end to terminate the Down Guy. The Big Grips and Thimbles will depend on the size of the Guy wire to be used 3/16EHS,1/4EHS or 5/16" EHS Strand(See Spec Sheet for Illustration)

ROHN ACWS Anti-Climb Warning Sign "Do Not Climb" for All Towers
Made in the USA!
This ROHN ACWS Anti Climb Warning Sign Kit is an OEM product from the ROHN Factory for placement on new tower installations and replacement on existing tower sites where the sign and sticker have faded due to exposure. Public Notice of "Do Not Climb" my Tower. One of the items on your yearly checklist.

ROHN AS455GTB Thrust Bearing Accessory Shelf for 45G 45GSR 55G Towers
Made in the USA!
The ROHN AS455GTB Thrust Bearing Accessory Shelf Assembly Bolts to either 45G, 45GSR or 55G Main Tower Section for Mounting Antenna Mast Thrust Bearing, Beacon Lights and other Attachments. Drilled to fit the TB3 and TB4 style Thrust Bearings, this plate is not drilled for use with a Rotor Unit. Field Drilling maybe necessary to accommodate Specific items.

ROHN APL55G Assembly Finishing Plate and Beacon/Lightning Rod Mount on 55G Tower
Made in the USA!
This ROHN APL55G Assembly Plate is a Finishing Top Cap that is also used for Mounting Beacon Lighting, Cameras or a Lightning Rod onto the final section of a 55G Tower. The APL55G Assembly Plate Bolts onto the top of a regular ROHN 55G Standard Main Tower Section (hardware included). Field Drilling may be necessary for mounting Beacons, Lighting, Cameras or other Accessories onto the Plate itself with hardware that should be sourced with the Accessory in question.
A Hole is already provided for mounting a LRCL Lightning Rod that comes with its own mounting hardware (only 1 needed, available separately).

ROHN AS455G Antenna Rotor Accessory Shelf for 45G 45GSR 55G Towers
Made in the USA!
The ROHN AS455G Antenna Rotor Accessory Shelf for 45G 45GSR 55G Towers Assembly Bolts to either 45G, 45GSR or 55G Main Tower Section for Mounting Antenna Mast Rotors, Beacon Lights and other Attachments. Drilled to fit the Yaesu style Antenna Rotors, this plate is not drilled for use with a Thrust Bearing. Field Drilling maybe necessary to accommodate Specific items.

ROHN 55JBK Replacement Bolt Kit for All 55G Standard Main Tower Sections
Made in the USA!
These ROHN 55JBK Bolts and Nuts are Hot Dip Galvanized like the Tower Section itself. Lasts Longer than the zinc plated versions. The Perfect Replacement Bolt Kit for high corrosion environments. This is the Exact same Bolt Kit contents you get inside the leg of each ROHN 55G Tower Main Section.
Factory OEM Product to the exacting specifications and Bolt Grades to assure Safety, Longevity and Reliability.