ROHN WM4 Antenna Wall Mount 4 inch W Style Brackets for 1.25 to 2.75 inch OD Mast
Made in the USA!
The ROHN WM4 is a Hot Dip Galvanized 14 Gauge Steel Bracket Set of (2) Heavy Duty "W" Style Brackets with Anti-Twist Feature and Hardware Included for a 4 inch Standoff Wall Support of Light and Medium Duty Antennas on Mast Poles from 5 to 10 feet long and from 1.25 to 2.75 inches in Outside Diameter including Telescopic Antenna Mast Poles for Off-air and OTA TV, UHF/VHF Radio, Remote Telemetry Control and Monitoring Stations, Cellular Date Gateways, WiFi, Wireless Internet, Receivers, Boosters and Repeaters.(Mast Not Included)

ROHN WM6S Antenna Wall Mount 6 inch Y Style Single Bracket for 1.25 to 2.75 inch OD Mast
Made in the USA!
The ROHN WM6S is a Hot Dip Galvanized 14 Gauge Steel Heavy Duty "Y" Style Single Bracket (1 each order) with Anti-Twist Feature and Hardware Included for a 6 inch Standoff Wall Support of Light and Medium Duty Antennas on Mast Poles from 5 to 10 feet long and from 1.25 to 2.75 inches in Outside Diameter including Telescopic Antenna Mast Poles for Off-air and OTA TV, UHF/VHF Radio, Remote Telemetry Control and Monitoring Stations, Cellular Date Gateways, WiFi, Wireless Internet, Receivers, Boosters and Repeaters.(Mast Not Included)

ROHN WM8S Antenna Mast Wall Mount 8 inch Single Y Style Bracket for 1.25 to 2.75 inch OD Mast Pole
Made in the USA!
The ROHN WM8S is a Hot Dip Galvanized 14 Gauge Steel Heavy Duty "Y" Style Single Bracket (1 each order) with Anti-Twist Feature and Hardware Included for an 8 inch Standoff Wall Support of Light and Medium Duty Antennas on Mast Poles from 5 to 10 feet long and from 1.25 to 2.75 inches in Outside Diameter including Telescopic Antenna Mast Poles for Off-air and OTA TV, UHF/VHF Radio, Remote Telemetry Control and Monitoring Stations, Cellular Date Gateways, WiFi, Wireless Internet, Receivers, Boosters and Repeaters.(Mast Not Included)

ROHN WM12S Antenna Wall Mount 12 inch Y Style Single Bracket for 1.25 to 2.75 inch OD Mast
Made in the USA!
The ROHN WM12S is a Hot Dip Galvanized 14 Gauge Steel Heavy Duty "Y" Style Single Bracket (1 each order) with Anti-Twist Feature and Hardware Included for a 12 inch Standoff Wall Support of Light and Medium Duty Antennas on Mast Poles from 5 to 10 feet long and from 1.25 to 2.75 inches in Outside Diameter including Telescopic Antenna Mast Poles for Off-air and OTA TV, UHF/VHF Radio, Remote Telemetry Control and Monitoring Stations, Cellular Date Gateways, WiFi, Wireless Internet, Receivers, Boosters and Repeaters.(Mast Not Included)

ROHN WM18S Antenna Wall Mount 18 inch Y Style Single Bracket for 1.25 to 2.75 inch OD Mast
Made in the USA!
The ROHN WM18S is a Hot Dip Galvanized 14 Gauge Steel Heavy Duty "Y" Style Single Bracket (1 each order) with Anti-Twist Feature and Hardware Included for an 18 inch Standoff Wall Support of Light and Medium Duty Antennas on Mast Poles from 5 to 10 feet long and from 1.25 to 2.75 inches in Outside Diameter including Telescopic Antenna Mast Poles for Off-air and OTA TV, UHF/VHF Radio, Remote Telemetry Control and Monitoring Stations, Cellular Date Gateways, WiFi, Wireless Internet, Receivers, Boosters and Repeaters.(Mast Not Included)

ROHN WM8D Antenna Wall Mount 8 inch Y Style Double Brackets for 1.25 to 2.75" OD Mast
Made in the USA!
The ROHN WM8D is a Hot Dip Galvanized 14 Gauge Steel Heavy Duty Bracket Set of (2) Double "Y" Style Brackets with Anti-Twist Feature, One with a Vertical Brace Strut on the Bottom Bracket, with Hardware Included for an 8 inch Standoff Wall Support of Light to Medium Duty Antennas on Mast Poles from 5 to 10 feet long and from 1.25 to 2.75 inches in Outside Diameter for Off-air and OTA TV, UHF/VHF Radio, Remote Telemetry Control and Monitoring Stations, Cellular Date Gateways, WiFi, Wireless Internet, Receivers, Boosters and Repeaters.(Mast Not Included)

ROHN WM12D 12" inch Stand-Off Antenna Mast Wall Mount Double "Y" Bracket Set
Made in the USA!
The ROHN WM12D is a Hot Dip Galvanized 14 Gauge Steel Heavy Duty Bracket Set of (2) Double "Y" Style Brackets with Anti-Twist Feature, One with a Vertical Brace Strut on the Bottom Bracket, with Hardware Included for a 12 inch Standoff Wall Support of Light to Medium Duty Antennas on Mast Poles from 5 to 10 feet long and from 1.25 to 2.75 inches in Outside Diameter for Off-air and OTA TV, UHF/VHF Radio, Remote Telemetry Control and Monitoring Stations, Cellular Date Gateways, WiFi, Wireless Internet, Receivers, Boosters and Repeaters.(Mast Not Included)

ROHN GTMBL Base Plate for Telescopic Pole and Antenna Mast 1-1/4" to 2-1/4" OD
Made in the USA!
This ROHN GTMBL Galvanized 9x9 inch 16 gauge Base Plate and Pier pin style Stake is for Ground Level Elevation installation of Telescopic and ANY Antenna Mast Poles from 1.25 to 2.25 inch Outside Diameter in both Temporary and Permanent Base Mounting by placement upon a Gravel or Concrete Foundation with the Center Stake inserted into, and the Plate resting on top of, a (1) Foot Cubed bed of gravel or pad of Poured Concrete above surrounding soil elevation.(depending on soil and frost conditions) The Pier Pin Style Center Stake Rod is approximately 1" in OD and floats freely within the Mast Tube placed over it and is not fixated other than by the Down Guys installed to secure the mast from wind-load.
Will Also Accommodate Telescopic Masts:
ROHN H20 H30 H40 H50 and Easy Up TM-20 TM-30 TM-40 TM-50
Manufacturers recommend that masts heights of 10 feet and higher above the uppermost bracket be guyed for Addition Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance

ROHN ETMB Roof Antenna Base Mount for Telescopic and Mast Pole up to 2-1/4" OD
Made in the USA!
This ROHN ETMB Universal Roof Antenna Mount Base is made for installing Telescopic and ANY Antenna Mast Poles up to 2.25 inch Outside Diameter on a Flat or Pitched Roof, providing your installation assures both structural and moisture barrier integrity. The Bottom of Mast inserts into the Hinged Clamp, Adjustable for Antenna Masts up to 2.25 inches in Diameter. Bonding should be made by affixment to Mast.
Will Also Accommodate Telescopic Masts:
ROHN H20 H30 H40 H50 and Easy Up TM-20 TM-30 TM-40 TM-50
Manufacturers recommend that mast heights of 10 feet and higher above the uppermost Support or Bracket be guyed for Addition Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance

ROHN UM20 Telescopic Antenna Mast Roof Mount for H20 on Flat, Slope or Peak
Made in the USA!
This is a Roof Mount Assembly specifically designed for placing an H20 Telescopic Antenna Mast on both the Flat Surface or Peak Ridgeline of the Roof, providing your installation assures both mechanical and vapor barrier integrity.

ROHN UM20 Telescopic Antenna Mast Roof Mount for H30 on Flat, Slope or Peak
Made in the USA!
This is a Roof Mount Assembly specifically designed for placing an H20 Telescopic Antenna Mast on both the Flat Surface or Peak Ridgeline of the Roof, providing your installation assures both mechanical and vapor barrier integrity.

ROHN UM40 Telescopic Antenna Mast Roof Mount for H30 on Flat, Slope or Peak
Made in the USA!
This is a Roof Mount Assembly specifically designed for placing an H40 Telescopic Antenna Mast on both the Flat Surface or Peak Ridgeline of the Roof, providing your installation assures both mechanical and vapor barrier integrity.

ROHN UM50 Telescopic Antenna Mast Roof Mount for H50 on Flat, Slope or Peak
Made in the USA!
This is a Roof Mount Assembly specifically designed for placing an H50 Telescopic Antenna Mast on both the Flat Surface or Peak Ridgeline of the Roof, providing your installation assures both mechanical and vapor barrier integrity.

ROHN WM18D 18" inch Stand-Off Antenna Mast Wall Mount Double "Y" Bracket Set
Made in the USA!
The ROHN WM18D is a Hot Dip Galvanized 14 Gauge Steel Heavy Duty Bracket Set of (2) Double "Y" Style Brackets with Anti-Twist Feature, One with a Vertical Brace Strut on the Bottom Bracket, with Hardware Included for an 18 inch Standoff Wall Support of Light to Medium Duty Antennas on Mast Poles from 5 to 10 feet long and from 1.25 to 2.75 inches in Outside Diameter for Off-air and OTA TV, UHF/VHF Radio, Remote Telemetry Control and Monitoring Stations, Cellular Date Gateways, WiFi, Wireless Internet, Receivers, Boosters and Repeaters.(Mast Not Included)

ROHN WM24S Antenna Wall Mount 24 inch Y Style Single Bracket for 1.25 to 2.75 inch OD Mast
Made in the USA!
The ROHN WM24S is a Hot Dip Galvanized 14 Gauge Steel Heavy Duty "Y" Style Single Bracket (1 each order) with Anti-Twist Feature and Hardware Included for a 24 inch Standoff Wall Support of Light and Medium Duty Antennas on Mast Poles from 5 to 10 feet long and from 1.25 to 2.75 inches in Outside Diameter including Telescopic Antenna Mast Poles for Off-air and OTA TV, UHF/VHF Radio, Remote Telemetry Control and Monitoring Stations, Cellular Date Gateways, WiFi, Wireless Internet, Receivers, Boosters and Repeaters.(Mast Not Included)

ROHN WM24D 24" inch Stand-Off Antenna Mast Wall Mount Double "Y" Bracket Set
Made in the USA!
The ROHN WM24D is a Hot Dip Galvanized 14 Gauge Steel Heavy Duty Bracket Set of (2) Double "Y" Style Brackets with Anti-Twist Feature, One with a Vertical Brace Strut on the Bottom Bracket, with Hardware Included for a 24 inch Standoff Wall Support of Light to Medium Duty Antennas on Mast Poles from 5 to 10 feet long and from 1.25 to 2.75 inches in Outside Diameter for Off-air and OTA TV, UHF/VHF Radio, Remote Telemetry Control and Monitoring Stations, Cellular Date Gateways, WiFi, Wireless Internet, Receivers, Boosters and Repeaters.(Mast Not Included)