LRCL-5 5' Foot x 5/8" Copper Clad Lightning Rod for Tower Plates, Caps & Leg Mounts
The LRCL is a 5' Foot x 5/8" Copper Clad Lightning Rod ONLY that comes threaded, with Nut and Washer Hardware, for mounting onto Tower Top Assembly Plates (i.e. ROHN APL25G, APL45G, APL55G, APL4A, APL4HA), Leg Mounts and Caps (i.e. ROHN VW133, VW132, VY1949A, VY1949-A) as well as extraneous Mounts such as the Harger CUBU581 Air Terminal Base.
Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose.

ROHN VW132 Lightning Rod Plate Kit for 45GSR Series Tower Cap Installation
Made in the USA!
The VW132 kit is comprised of (1) 3/16" inch thick Plate with bolts and nuts for installation onto a 45GSR Tower Section leg joint flange as an Assembly for (1) Leg with an additional Hole predrilled for the LRCL Lightning Rod.(available separately). Addition Top Caps are not included in this Kit as only One Lightning Rod is needed and with the leg rails of the Tower section being solid, there is no further need of additional caps to seal from Animal, Insect or Debris accumulation.

ROHN VW133 Lightning Rod Plate Kit for 65G Series Tower Cap Installation
Made in the USA!
The VW133 kit is comprised of (1) 3/16" inch thick Plate with bolts and nuts for installation onto a 65G Tower Section leg joint flange as an Assembly for (1) Leg with an additional Hole predrilled for the LRCL Lightning Rod.(available separately). Two (2) Addition Non-Rod Top Caps with bolts and nuts are included in this Kit as only One Lightning Rod is needed and with the leg rails of the Tower section being hollow, there is further need of additional caps to seal all (3) Rails from Animal, Insect and Debris accumulation.

ROHN VY1949-A Lightning Rod Mounting Kit for Round Tower Leg or Antenna Pipe Mount 2.38"-4.5" OD
Made in the USA!
The ROHN VY1949-A Lightning Rod Clamp-on Mounting Kit is designed to attach a 5/8" Diameter LRCL Lightning Rod (available separately) onto ANY Round ROHN Tower Leg, Antenna Mast Pole or Antenna Pipe Mount having a 2.38" to 4.50" OD and consists of a Hot Dip Galvanized Angle Iron Mount that comes with (2) U-bolts and Nuts available in four sizes; 2.50", 3.00", 3.50" and 4.50" Inside Diameter. Also for installation onto ROHN 80/90 and RTL Towers. Verify the OD of the Leg, Pole or Pipe you wish to attach to, then select the U-bolt Clamp Inside Diameter size accordingly.
For attachment to round members and pipes of 1.25" to 2.5" inch OD, please see the VY1949A

LRCL-4 4' Foot x 5/8" Copper Clad Lightning Rod for Tower Plates, Caps & Leg Mounts
The LRCL-4 is a 4' Foot x 5/8" Copper Clad Lightning Rod ONLY that comes threaded, with Nut and Washer Hardware, for mounting onto Tower Top Assembly Plates (i.e. ROHN APL25G, APL45G, APL55G, APL4A, APL4HA), Leg Mounts and Caps (i.e. ROHN VW133, VW132, VY1949A, VY1949-A) as well as extraneous Mounts such as the Harger CUBU581 Air Terminal Base.
Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose.

LRCL-3 3' Foot x 5/8" Copper Clad Lightning Rod for Tower Plates, Caps & Leg Mounts
The LRCL-3 is a 3' Foot x 5/8" Copper Clad Lightning Rod ONLY that comes threaded, with Nut and Washer Hardware, for mounting onto Tower Top Assembly Plates (i.e. ROHN APL25G, APL45G, APL55G, APL4A, APL4HA), Leg Mounts and Caps (i.e. ROHN VW133, VW132, VY1949A, VY1949-A) as well as extraneous Mounts such as the Harger CUBU581 Air Terminal Base.
Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose.

LRCL-8 8' Foot x 5/8" Copper Clad Lightning Rod for Tower Plates, Caps & Leg Mounts
The LRCL-8 is a 8' Foot x 5/8" Copper Clad Lightning Rod ONLY that comes threaded, with Nut and Washer Hardware, for mounting onto Tower Top Assembly Plates (i.e. ROHN APL25G, APL45G, APL55G, APL4A, APL4HA), Leg Mounts and Caps (i.e. ROHN VW133, VW132, VY1949A, VY1949-A) as well as extraneous Mounts such as the Harger CUBU581 Air Terminal Base.
Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose.

ROHN VY1949A Lightning Rod Mounting Kit for Round Tower Leg or Antenna Pipe Mount 1.25"-2.5" OD
Made in the USA!
The ROHN VY1949A Lightning Rod Clamp-on Mounting Kit is designed to attach a 5/8" Diameter LRCL Lightning Rod (available separately) onto ANY Round ROHN Tower Leg, Antenna Mast Pole or Antenna Pipe Mount having a 1.25" to 2.50" OD and consists of a Hot Dip Galvanized Angle Iron Mount that comes with (2) U-bolts and Nuts. For installation onto ROHN 25G, 45G, 45GSR, 55G, and 65G Towers. Verify the OD of the Leg, Pole or Pipe you wish to attach to, then select the U-bolt Clamp Inside Diameter size accordingly.
For attachment to round members and pipes of 2.5" to 4.5" inch OD, please see the VY1949-A

ROHN AGK1GGX Tower Down Guy Anchor Rod Ground Kit
REV. G Kit. Comprises enough material to ground 3 Anchors. Comes with (3) Ten Foot Ground Rods, (3) Ground Rod Clamps , (3) CPC.5/.75 Anchor Rod Clamp (not included in separate kits from ROHN, but included here) and (3)10 Feet of 7/16  Wire Rope...
This Item Ships LTL Freight ONLY...

ROHN BGK3GGX-1 Tower Base Section Grounding Kit 25G.45G,45GSR,55G,65G and Roof Bases

Made in the USA!The ROHN BGK3GGX-1 is primarily used for grounding the Base Section or Plate  for 25G.45G,45GSR,55G,65G and Roof Bases Towers. Comprises enough material to ground at 1 Tower section joint bolt location. Consists of (1) 15' of 7/16 6x25 EIP IWRC RRL Wire Rope ,(1) 5/8" x 8 Foot  HDG  Ground Rod ,(1) 3/4 Inch Ground Rod Clamp ,(1) CPC1/1.25 Connection Clamp to Section Tubular Rail.  The NEW REV. G Tower structure Grounding Kits use wire rope vs. the solid copper found here, in addition to revised clamping Attachments. 
This Item Ships UPS Package!

ROHN CPC.5/.75 Clamp for Grounding Tower Down Guy Anchor Rods
Made in the USA!
The CPC.5./.75 Clamp is for Solid and Stranded Copper Wire and Stranded Wire Rope Grounding Connections to the Rod segment of Down Guy Anchors for ROHN Tower Down Guys, by means of affixing these 0.5 to 0.75 inch range Clamps around the solid Rod (0.375 to 1.00 inch actual OD range) component of their Down Guy Anchors that are poured in Concrete. The Clamp Lug also mates the connection to Solid/Stranded Copper or 7/16 6x25 EIP IWRC RRL Wire Rope as supplied in the AGK3GGX REV. G Grounding Kits (not included).
Harger CPC Pipe Ground Clamps compare to Burndy GAR

ROHN CPC1/1.25 Clamp for Grounding 25G 45G Tower and Base Sections
Made in the USA!
The CPC1/1.25 Clamp is for Solid and Stranded Copper Wire and Stranded Wire Rope Grounding Connections to the ROHN 25G and 45G Main Tower Sections and Fixed Rigid Bases by means of affixing these 1.0 to 1.25 inch range Clamps around at any one of the (3) Tubular Rail (0.9375" - 1.7" OD actual range) components at the lowest visible point possible above grade and in closest proximity to the Ground intended for use as to shorten the wire distance between as much as possible. The Lug also mates the connection to Solid/Stranded Copper or 7/16 6x25 EIP IWRC RRL Wire Rope as supplied in the BGK3GGX REV. G Grounding Kits (not included).
Harger CPC Pipe Ground Clamps compare to Burndy GAR

ROHN BGK3GGX Tower Base Section Grounding Kit for 25G,45G,45GSR,55G,65G and Roof Bases 
New REV. G Grounding Kit for 25G and 45G Guyed Towers. Comprises enough material to ground 1 Tower Base Section Tubular Rail ...

ROHN AGK1G Tower Down Guy Wire Grounding Kit
REV. F Kit. Comprises enough material to ground 3 Down Guy Anchor locations. Comes with (3) Ten Foot Ground Rods, (3) Ground Rod Clamps and 45 Feet ( 3 x 15' ) of #4 Stranded Copper Wire. Select Guy Wire Ground Clamps by Guy Wire size below (see Accessories for this Item)...

3 Star Inc GC-2 Bronze Grounding Clamp for Tower Antenna Mast Pole Pipe Section 1.25" to 2 inch OD
The GC-2 is a Cast Bronze Pipe Clamp that affixes to 1.25" to 2.00 inch OD Tower Section Rails, Base and Antenna Mast, Telescopic Mast Pole, and Pipe, used for Grounding Connections to Ground Rods accommodating Wire from #4 stranded to #10 SOL AWG.
The mirror Back half section is reversible and can be used on ROHN 25G, 45G, 55G and 65G Tower Sections and Bases as well as Universal Towers. Accommodating the most common Antenna Mast, Telescopic Mast Poles and Tower Section Rail sizes from 1.25" to 2 inch OD, remember that the Lowermost section for TM-50 and H-50 Telescopic Masts are 2.25 inches in OD and will not fit.

3 Star Inc CW4S-10 #4 Solid Bare Copper Wire Available in Contiguous 10 Foot Coils
The CW4S-10 Part number is for Ordering 10 feet of #4 Solid Bare Copper Wire used in REV. F Grounding Kits and Arrays of ROHN and Universal Towers in addition to Anchors when Guyed. REV. F Copper Ground Wire Grounding is Installed with Clamps to secure a connection to the Tower Base or Main Section Rail and then run a short distance in attachment to Copper-clad Ground Rods. Satisfactory Grounding is typically achieved through use of separate runs from (2) or more Tower Base Rails, to (1) or more Ground Rods. Priced and Sold in 10' Foot increments for Contiguous Hank Segments for total roll QTY up to 50 Feet, comprising of 10 ft. per unit ordered.

3 Star Inc CW6S-10 #6 Solid Bare Copper Wire Available in Contiguous 10 Foot Coils
The CW46S-10 Part number is for Ordering 10 feet of #6 Solid Bare Copper Wire used in REV. F Grounding Kits and Arrays of ROHN and Universal Towers in addition to Anchors when Guyed. REV. F Copper Ground Wire Grounding is Installed with Clamps to secure a connection to the Tower Base or Main Section Rail and then run a short distance in attachment to Copper-clad Ground Rods. Satisfactory Grounding is typically achieved through use of separate runs from (2) or more Tower Base Rails, to (1) or more Ground Rods. Priced and Sold in 10' Foot increments for Contiguous Hank Segments for total roll QTY up to 50 Feet, comprising of 10 ft. per unit ordered.

ROHN BGK2GGX Tower Base Section Grounding Kit
New REV. G Grounding Kit for 55G and 65G Guyed Towers. Comprises enough material to ground 1 Tower Base Section Tubular Rail. Consists of (1) 5/8"x10' Ground Rod, (1) Rod Clamp (1) CPC1.5/2 Rail Clamp and 15 feet of 7/16 6x25 EIP IWRC RRL Wire Rope...

ROHN IWRC 7/16 6x25 EIP IWRC RRL Wire Rope 
New REV. G Grounding cable for use on ROHN Tower Systems. Used for grounding both the tower and down guy components with CPC clamps and Galvanized ground rods (not included). Price is per foot. Enter number of feet desired in quantity box above.

ROHN BGK1GGX Tower Base Section Grounding Kit
New REV. G Grounding Kit for 25G and 45G Guyed Towers. Comprises enough material to ground 1 Tower Base Section Tubular Rail. Consists of (1) 5/8"x10' Ground Rod, (1) Rod Clamp (1) CPC1/1.25 Rail Clamp and 15 feet of 7/16 6x25 EIP IWRC RRL Wire Rope...

ROHN CPC1.5/2 Clamp for Grounding 55G 65G Tower and Base Sections
Made in the USA!
The CPC1.5/2 Clamp is for Solid and Stranded Copper Wire and Stranded Wire Rope Grounding Connections to the 55G and 65G Main Tower Sections and Fixed Rigid Bases by means of affixing these 1.5 to 2.00 inch range Clamps around at any one of the (3) Tubular Rail (1.25" - 2.4" OD actual range) components at the lowest visible point possible above grade and in closest proximity to the Ground intended for use as to shorten the wire distance between as much as possible. The Lug also mates the connection to Solid/Stranded Copper or 7/16 6x25 EIP IWRC RRL Wire Rope as supplied in the BGK3GGX REV. G Grounding Kits (not included).
Harger CPC Pipe Ground Clamps compare to Burndy GAR

ROHN R-340020 5/8" x 8' Bonded Ground Rod
Uniform Electrolytic Copper On Steel Core, Minimum Copper Depth 10 Mils, UL Listed. Use 5/8 inch Ground Rod Clamp for #6, #4 copper, use 3/4 inch clamp with steel wire rope (sold separately). Suitable for burial after attachment (see our self amalgamating tape sealant). Use for REV. F Grounding of Tower Base and Down Guys or Telescopic Antenna Masts. Select a ground rod clamp based on conductor to be attached (see details)...

ROHN BGK2G Tower Base Section Grounding Kit REV F
Made in the USA!
The ROHN BGK2G is primarily used for grounding the Base Section or Plate of 25G,45G,55G and 65G REV. F Towers, also used in Self-Supporting Tower Kits. Comprises enough material to ground at 1 Tower section on Tubular Rail. Consists of (1) 5/8"x8' Ground Rod, (1) 5/8"x8' Ground Rod Clamp (1) 1-1/4 to 2" inch J-Clamp and 10 feet of #4 Solid Copper Wire. These are REV. F Tower structure Grounding Kits. The NEW REV. G Tower structure Grounding Kits use wire rope vs. the solid copper found here, in addition to revised clamping Attachments. (see BGK2GGX)
Terminal Lug does NOT come compressed onto the copper wire from the Factory.
This Item Ships UPS Package!

GR8GROD 5/8" x 8' Galvanized Ground Rod
Galvanized over Electrolytic Copper On Steel Core. Use 5/8 inch Ground Rod Clamp for #6, #4 copper, use 3/4 inch clamp with steel wire rope (sold separately). Suitable for burial after attachment (see our self amalgamating tape sealant). Use for REV. F Grounding of Tower Base and Down Guys or Telescopic Antenna Masts. Select a ground rod clamp based on conductor to be attached (see details)...

ROHN R-340021 5/8" x 10' Bonded Ground Rod
Uniform Electrolytic Copper On Steel Core, Minimum Copper Depth 10 Mils, UL Listed. Use 5/8 inch Ground Rod Clamp for #6, #4 copper, use 3/4 inch clamp with steel wire rope (sold separately). Suitable for burial after attachment (see our self amalgamating tape sealant). Use for REV. F Grounding of Tower Base and Down Guys or Telescopic Antenna Masts. Select a ground rod clamp based on conductor to be attached (see details)...

TnB TNB4014 G5 5/8 inch Bronzed Ground Rod Clamp
Appears on the DISH Network Approved List!
Cast of high-strength corrosion-resistant Bronze. UL listed for direct burial. Furnished with hex head bolts. Simplified, compact design makes lasting, trouble-free connection...

3 Star GRC-3/4 3/4 inch Bronzed Ground Rod Clamp
Cast of high-strength corrosion-resistant Bronze. UL listed for direct burial. Furnished with hex head bolts. Simplified, compact design makes lasting, trouble-free connection to Wire Range #10 Solid through #2 Stranded. Suitable for burial after attachment (see our self amalgamating tape sealant). Use for REV. G Grounding of Tower Base and Down Guys onto 5/8 inch Ground Rods using the 7/16 wire rope ground specified. Select Ground Rod length by application (see details)...

GR-4 -  5/8" x 4' Bonded Ground Rod
Uniform Electrolytic Copper On Steel Core, Minimum Copper Depth 10 Mils, UL Listed. Use 5/8 inch Ground Rod Clamp for #6, #4 copper, use 3/4 inch clamp with steel wire rope (sold separately). Suitable for burial after attachment (see our self amalgamating tape sealant). Use for Grounding of Tower Base and Down Guys or Telescopic Antenna Masts. Select a ground rod clamp based on conductor to be attached (see details)...

GR8GROD 5/8" x 10' Galvanized Ground Rod

A Galvanized ground rod that is 5/8 in. nominal in diameter with a length of 10 ft . Zinc-Coated exteriors are hot-dip galvanized for solid protection against corrosion , The ground rod meets NEC , UL and in accordance with ASTM® , use 5/8 inch Ground Rod Clamp for #6, #4 copper, use 3/4 inch clamp with 7/16 inch IWRC wire rope (sold separately). Suitable for burial after attachment (see our self amalgamating sealant tape). Use for REV. F Grounding of Tower Base and Down Guys or Telescopic Antenna Masts. Select a ground rod clamp based on conductor to be attached (see details).......