ROHN R-JR45A Replacement U Bolt for AS25G RP25G UHF25G
Factory OEM, Original Manufacturer's (1) U Bolt and (2) Nuts per Order as direct replacement for Accessory Rotor Shelf, Rotor Post or UHF Antenna Mount that is used for Mounting Antenna Rotor, Beacon Lights, Whip Antennas and other Attachments...

ROHN BPL25G Thrust Bearing Plate and Down Guy Top Cap for 25G Tower
Made in the USA!
The ROHN BPL25G Thrust Bearing Top Cap Plate bolts onto the top of any Standard ROHN 25G Main Tower section of 10, 7, 5 or 3 foot in height and with long legs, can provide extra clearance for installation of equipment such as Rotors on an Accessory Shelf mounted on a section below. The BPL25G is pre-drilled to accept mounting for the ROHN Thrust Bearing TB3 or TB4 and also provides Down Guy Attachment to this very same plate via Shackles and Thimbles.(Not Included)

ROHN TB3 2" inch Heavy Duty Thrust Bearing for 25G 45G 55G Series Towers
Made in the USA!
The ROHN TB3 Thrust Bearing is pre-drilled to mount onto ROHN G-Series Tower Top Cap Sections and Plates like the 25AG4, BPL25G, BAS25G, 45AG4, BPL45G and BPL55G that are in turn, pre-drilled to accept the TB3 in support of up to 2.00" OD Mast. The TB3 is not intended to be mounted onto AS25G or AS455G Accessory shelves. The Rotor can then be Mounted on these Accessory Shelves Below.

ROHN TB50 Bushing fits 20BG 25AG 45AG Top Cap Section for 1.25" OD Antenna Mast
Made in the USA!
The ROHN TB50 Die Cast Mast Tube Reducer Bushing fits 20BG 25AG 45AG Top Cap Sections for installing a 1.25" OD Antenna Mast in the Mast Tube of these Sections. The 20BG and 25AG Top Cap Sections come with a (1) Removable 1.25" ID Bushing at the Top end of the Mast Tube on the Pinnacle of the Section that can knocked out as only a couple tack welds hold it in place. The TB50 can be used as a replacement for this end as well as providing the bushing necessary at the bottom end to center the 1.25" Antenna Mast you are looking to install. The 45AG Mounting Tube is open at both ends.

ROHN RP25G Single Rotor Post 1.25"OD for Small Antenna on 25G Series Tower
Made in the USA!
The ROHN RP25G is for Mounting Antenna Rotors onto a 1.25 DIA x 7.5inch post. Fastens with Saddle Clamps to the Tower leg (also 1.25 inch DIA), with 4.75 inches of clear space between Tower Rail mount and Rotor Post.

ROHN RP25G CM Double Rotor Post 1.25"OD for Antenna Array on 25G Series Tower
Made in the USA!
The ROHN RP25GCM Antenna Rotor Post is Galvanized Steel T-tube Post with (2) U-bolts to attach to any Side Rail anywhere on a 25G Tower Section for Mounting a Special CM Attachment Style Light Duty Antenna Rotor or Array onto the Post. Fastens with Saddle Clamps.

ROHN SR245 Safety Ring Attachment for 25G 45G 45GSR Tower Installation or Service
Made in the USA!
The SR245 Snaps into place at any level with No bolts required. This attachment fits the ROHN 25G, 45G, 45GSR Tower Series and Compliments the Work Platform Accessory (WP25G for 25G and WP45G for the 45G, Not included). These Accessories, along with your safety harness, provides a Safe Work Space Environment at any Tower Height.

ROHN WP25G Work Platform Attachment for 25G 45G 45GSR Tower Installation or Service
Made in the USA!
The WP25G Snaps into place at any Tower level with No bolts required. This attachment fits the ROHN 25G Tower Series and Compliments the Safety Ring Accessory (SR245 Not included). These Accessories, along with your Safety Harness, provides a Safe Work Space Environment at any Tower Height.

ROHN ACL25G Anti-Climb Panels Safety Accessory for 25G Tower Section
Made in the USA!
These ROHN ACL25G Anti-Climb Panel Kit consists of (3) Panels with associated Hardware are Installed for Protection and Public Safety on each Face of the Bottom 25G Tower Section. Search for the ACL models for the other ROHN Tower Series. Together with ACWS Anti-Climb Warning Sign and appropriate fencing, these panels help protect your Tower from Unauthorized Climbing Activities
This Item Ships LTL Freight ONLY!

ROHN TB4 3" inch Heavy Duty Thrust Bearing for 25G 45G 55G Series Towers
Made in the USA!
The ROHN TB4 Thrust Bearing is pre-drilled to mount onto ROHN G-Series Tower Top Cap Sections and Plates like the 25AG4, BPL25G, BAS25G, 45AG4, BPL45G and BPL55G that are in turn, pre-drilled to accept the TB4 in support of up to 3.00" OD Mast. The TB4 is not intended to be mounted onto AS25G or AS455G Accessory shelves. The Rotor can then be Mounted on these Accessory Shelves Below.

ROHN HBHDW Replacement Clamp Set for HB25AG HB25BG HB25CG EB2525G House Brackets
Made in the USA!
This ROHN HBHDW Bracket Hardware Kit is a Factory OEM, Original Manufacturer's Kit comprised of; (2) U-Bolts, (4) Nuts, (4) Washers, (4) Saddles, (2) Adjustment Bolts, (2) Lock Washers and (2) Nuts per Order as direct replacement parts for HB25AG, HB25BG, HB25CG and EB2525G.

ROHN KY2041A Waveguide Cable Hanger Bracket for 25G 45G 45GSR 55G 65G Tower
Made in the USA!
The ROHN KY2041A 3-hole Waveguide Cable Bracket is used to secure Waveguide Cable Lines to the legs of standard ROHN 25G 45G 45GSR 55G 65G tower sections. The hot-dip galvanized brackets feature (3) 7/16 and (3) 3/4 holes and can be mounted to Tower Section Rail Legs from 3/4 - 2 1/4" inch in Outside Diameter. It is recommended that (5) KY2041A be used per 20ft of tower for 4ft OC spacing.(1 per Quantity Ordered)

ROHN R-JR45GA Replacement U Bolt for AS25G RP25G UHF25G
Factory OEM, Original Manufacturer's (1) U Bolt and (2) Nuts per Order as direct replacement for Accessory Rotor Shelf, Rotor Post or UHF Antenna Mount that is used for Mounting Antenna Rotor, Beacon Lights, Whip Antennas and other Attachments...

ROHN BPC25G Concrete Base Plate for 25G Guyed Tower
Made in the USA!
The ROHN BPC25G uses a 3/4" x 12" pier pin to align the plate to the concrete slab and prevents Lateral Movement for ROHN 25G Guyed Tower installations only. This ROHN Base Plate is 15 inches Square and 3/16 Thick, allows the ROHN 25G Tower to be Mounted onto an existing or new Concrete Pier, Pad or Slab but Cannot be Used as a Self Supporting Base Plate.(see 25GSSB)
All 25G Tower Installations should be temporarily Guyed during erection.

ROHN PR25G Peak Roof Mount Base for 25G Guyed Tower Installation
Made in the USA!
The PR25G has adjustable hinged feet to conform to nearly any roof pitch and bolts to roof surface. This Rohn Base Plate allows the ROHN 25G Tower to be Mounted onto a pitched roof peak when the Roof Structure is reinforced and 25G Tower is guyed, but Cannot be Used as a Self Supporting Base Plate (see R-25GSSB). There is no Wind Load vs. Height Guidance to be found this type of Mounting in any of the Specification Literature for good reason. You need to Consult an Engineer to determine the Load Bearing Capability and Wind Speed Survivability of such an Installation. Guying is an absolute must, but remember that guying will simply increase the down pressure onto the Base support, which in this case, is your Roof!

ROHN FR25G Flat Roof Mount Base for 25G Guyed Tower on Building
Made in the USA!
The ROHN FR25G bolts directly onto a Watertight and Reinforced Flat Roof Surface for a 25G Guyed Tower, but Cannot be Used as a Self Supporting Base Plate. (see 25GSSB or 25GBRM) Roof Mounted Tower Options may limit Potential Height considerably as there is no Wind Load vs. Height Guidance to be found this type of Mounting in any of the Specification Literature for good reason. You need to Consult an Engineer to determine the Load Bearing Capability and Wind Speed Survivability of such an Installation. Guying is an absolute must, but remember that guying will simply increase the down pressure onto the Base support, which in this case, is your Roof!

ROHN SDB25G Single Drive-In Base for Temporary Ground Mount of 25G Guyed Tower
Made in the USA!
allows the ROHN 25G Tower to be Mounted directly onto the Ground for Temporary Guyed or Bracketed Tower configurations.

ROHN KH8175A Template and Bolt Kit for 25GSSB Base Plate Installation of 25G Self-Supporting Tower
Made in the USA!
The ROHN KH8175A is a Template and Base Bolts Kit used in preparation of a freshly poured concrete pad installation of the ROHN 25GSSB Self-Supporting 25G Tower Base Plate
The KH8175A Kit includes Template with (4) Base Bolts.(25GSSB Self-Supporting Base Plate not included)

ROHN 3/4X12PP Pier Pin 3/4" x 12" inch installed for 25G 45G 55G Concrete Base Plates
Made in the USA!
The ROHN 3/4X12PP Pier Pin is a 3/4 inch DIA x 12 inch long Hot Dip Galvanized Steel Rod Section used to align the BPC25G BPC45G BPC55G Concrete Base Plates on top of a Concrete Pier to prevent lateral movement only.(Concrete Base Plate is a Separate Item) The ROHN 25G 45G 55G Guyed Towers are then erected Over Center of the Pier Pin held Concrete Base Plate. Without Torque Arm Supplemented Down Guys, the Tower may twist slightly as the guys merely keep the tower plumb and centered but do not prevent twist under load. A Short Base or Main Tower Section Embedded in a concrete pour foundation will reduce this affect tremendously and a Torque Arm Assembly installed in proximity to the location of the Antennas mounted on the tower will minimize it further.
A Concrete Base Plate cannot be used as a Self Supporting Base Plate (see 25GSSB 45GSSB 55GSSB).
This Pier Pin is also used with 25TG 45TG 55TG Tapered Base Sections.

ROHN 25GBRM BRM6X Non-Penetrating Roof Mount Base for 25G Tower
Made in the USA!
The ROHN 25GBRM non-penetrating roof mount, is designed to support up to (2) 25G tower sections of 25G tower in self-supporting tower applications. The base of the roof mount is 10’ square with a 16” tray to fit the concrete blocks, typically used as ballast. Height and Antenna Loading capability are dependent upon ballast weight. You need to Consult an Engineer to determine the Load Bearing Capability of the roof that you are entertaining such an Installation. Please refer to the Chart (pdf link above) which is a great place to start in determining whether your circumstances qualify for such an installation. The mount is Hot Dip Galvanized for corrosion protection and goes together quickly.
This Item Ships LTL Freight ONLY!

ROHN 25GSSB Concrete Base Plate for 25G Self-Supporting Tower
Made in the USA!
The ROHN 25GSSB Base Plate for 25G Self-Supporting Tower is 19 inches Square and 1/2 Thick, allows the ROHN 25G Tower to be Mounted onto an Engineered Concrete Pad for this Purpose with Four (4) J-bolts (5/8 inch DIA by 12 inch long) or Equivalent embedded in a Poured Concrete Pier Pad, placed 16" inches square (Center to Center) and can be used as the Base Plate for Self-Supporting 25G Tower Installations, depending on Wind Load. This is outside the Catalog of Pre-Engineered Self-Supporting Tower kits that use an entire base section embedded into the concrete during pour.
All 25G Tower Installations should be temporarily Guyed during erection.
(Bolts sold separately).
(ROHN KH8175A Template and Bolt Kit available OPTIONAL)
(Engineering notes in Spec. Sheets)
Be sure to check out the Ice, Wind and Antenna Load Specifications for your area that determine Maximum Self-Supporting 25G Tower Height.

ROHN BPH25G Hinged Base Plate for 25G Guyed or Bracketed Tower
Made in the USA!
The ROHN BPH25G Hinged Base Plate for 25G Guyed or Bracketed Towers is Bolted to a Concrete Pier Placement. The BPH25G is pre-drilled for use with six (6) 1/2 x 12 inch J-Bolts or Equivalent Embedded in Concrete Pier Pad during pour(Seek Engineering notes in Spec. Sheets, J-bolts Sold Separately), and Allows for the Tower to be Rotated up from Base during Installation. This ROHN Base Plate is 15 inches Square for the ROHN 25G Tower to be Mounted on a new or existing Concrete Pier. This Base for the 25G tower can be used in guyed or bracketed, but not self-supporting configurations according to specifications in the ROHN catalog.
All 25G Tower Installations should be temporarily Guyed during erection.
Consult ROHN Catalog Links at Footer Section below for ROHN 25G Tower Details.

3 Star Inc 1/2X12BB Base Bolt 1/2" by 12' inch J-Bolt for ROHN BPH25G and 45GSSB Base Plate
The 1/2X12BB Base Bolt is for embedment inclusion during the Concrete Pier Pad Pouring Process that precedes the mounting of a ROHN BPH25G Hinged and ROHN 45GSSB Base Self-Supporting Tower Base Plate.(Not Included) This BPH25G Hinged Base Plate is pre-drilled to mount upon (6) Six of these, and the 45GSSB is pre-drilled to mount upon (12) of these 1/2 inch OD x 12 inch Length J-Bolts with a space in between the finished slightly crowned concrete and the Bottom of the Base Plate for Drainage.(Seek Engineering notes in Spec. Sheets) Make a template for pouring Concrete while suspending these J-bolts during the pouring process.(One Bolt per Order)
Assure that the Down Guys or Wall Brackets match the direction of the Hinged Plate Travel Path.

3 Star Inc 5/8X12BB J Bolt 5/8" x 12" inch for ROHN BPH45G and 25GSSB Base Plate
The 5/8X12BB Base Bolt is for embedment inclusion during the Concrete Pier Pad Pouring Process that precedes the mounting of a ROHN BPH45G Hinged Base Plate for 45G Guyed or Bracketed Tower that is pre-drilled to mount upon (6) Six of these and the ROHN 25GSSB Self-Supporting Base Plate for 25G Self-Supporting Tower which uses Four (4) of these 5/8 x 12 inch J-bolts (Seek Engineering notes in Spec. Sheets) with a space in between the finished slightly crowned concrete and the Bottom of the Base Plate for Drainage.(Seek Engineering notes in Spec. Sheets) Make a template for pouring Concrete while suspending these J-bolts during the pouring process.(One Bolt per Order)
Assure that the Down Guys or Wall Brackets match the direction of the Hinged Plate Travel Path.

LRCL-5 5' Foot x 5/8" Copper Clad Lightning Rod for Tower Plates, Caps & Leg Mounts
The LRCL is a 5' Foot x 5/8" Copper Clad Lightning Rod ONLY that comes threaded, with Nut and Washer Hardware, for mounting onto Tower Top Assembly Plates (i.e. ROHN APL25G, APL45G, APL55G, APL4A, APL4HA), Leg Mounts and Caps (i.e. ROHN VW133, VW132, VY1949A, VY1949-A) as well as extraneous Mounts such as the Harger CUBU581 Air Terminal Base.
Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose.

LRCL-4 4' Foot x 5/8" Copper Clad Lightning Rod for Tower Plates, Caps & Leg Mounts
The LRCL-4 is a 4' Foot x 5/8" Copper Clad Lightning Rod ONLY that comes threaded, with Nut and Washer Hardware, for mounting onto Tower Top Assembly Plates (i.e. ROHN APL25G, APL45G, APL55G, APL4A, APL4HA), Leg Mounts and Caps (i.e. ROHN VW133, VW132, VY1949A, VY1949-A) as well as extraneous Mounts such as the Harger CUBU581 Air Terminal Base.
Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose.

LRCL-3 3' Foot x 5/8" Copper Clad Lightning Rod for Tower Plates, Caps & Leg Mounts
The LRCL-3 is a 3' Foot x 5/8" Copper Clad Lightning Rod ONLY that comes threaded, with Nut and Washer Hardware, for mounting onto Tower Top Assembly Plates (i.e. ROHN APL25G, APL45G, APL55G, APL4A, APL4HA), Leg Mounts and Caps (i.e. ROHN VW133, VW132, VY1949A, VY1949-A) as well as extraneous Mounts such as the Harger CUBU581 Air Terminal Base.
Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose.

LRCL-8 8' Foot x 5/8" Copper Clad Lightning Rod for Tower Plates, Caps & Leg Mounts
The LRCL-8 is a 8' Foot x 5/8" Copper Clad Lightning Rod ONLY that comes threaded, with Nut and Washer Hardware, for mounting onto Tower Top Assembly Plates (i.e. ROHN APL25G, APL45G, APL55G, APL4A, APL4HA), Leg Mounts and Caps (i.e. ROHN VW133, VW132, VY1949A, VY1949-A) as well as extraneous Mounts such as the Harger CUBU581 Air Terminal Base.
Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose.

ROHN GA25GD Down Guy Bracket Assembly for 25G Guyed Tower Installation
Made in the USA!
The GA25GD Mounts to the ROHN 25G Series Guyed Towers at any Horizontal Brace. This Guy Assembly is used to attach guy wires to the ROHN 25G tower. It is recommended as an Attachment to a ROHN 25G Tower Section for use at every guy level. This GA25GD Guy Bracket is an essential part of your ROHN 25G Guyed Tower Installation. Install the Guy Brackets at Heights indicated by the ROHN Catalog as per REV. G or REV. F Wind Load Ratings.

ROHN TA25 Torque Arm Stabilizer Anti-Twist Down Guy Assembly for 25G Tower
Made in the USA!
This ROHN TA25 Torque Arm Anti-twist Stabilizer Down Guy Assembly is to be located in the area of the Microwave or other Focused Beam antennas to provide six-way guying. The Assembly Comes welded as (1) Piece and attaches to the Tower at any Section Joint using slightly longer Joint Bolts through each Rail as the Sections Join Together.(included)
MUST BE INSTALLED AS SECTIONS ARE JOINED TOGETHER.
You will Need (6) 1/2" Shackles with a thimble around each shackle to seat whichever size EHS Strand Big Grip Preform Dead-end to terminate the Down Guy. The Big Grips and Thimbles will depend on the size of the Guy wire to be used 3/16EHS,1/4EHS or 5/16" EHS Strand(See Spec Sheet for Illustration)

ROHN TB25D Torque Bar Stabilizer Accessory for GA25GD Guy Bracket Assembly
Made in the USA!
This is (1) Bar per Order, needing (3) in total to complete a 3-way down guy configuration. This Accessory Modifies a New or Existing GA25GD Down Guy Bracket Assembly (Not included) into a Torque Stabilizer Assembly that would be installed at existing Guy attachments on any horizontal brace as opposed to tower section joints as provided for by the TA25 (Not included) Stabilizer Assembly which would require additional Down Guy Attachments. This Item will also require the purchase of 3/8" inch shackles to complete the upgrade.

ROHN ROHNJACK Alignment Assembly/Disassembly Tool for ROHN 20G 25G 45G 55G Tower Section
Made in the USA!
The ROHNJACK is used to Assemble/Disassemble ROHN Tower Sections and Align Tower Legs during assembly and Tower erection. It is Not a Gin Pole but works together with one for easy removal and assembly of ROHN Tower Sections. It designed to fit 20, 25G, 45G, and 55G ROHN Tower Sections (Leg alignment tool will not fit 55G, but it will assemble and disassemble sections)
This Tool does not take the place of a Gin Pole in the physical lifting of Tower Sections but rather, works in concert with one for Tower Erection and Teardown

ROHN GB25D Single Replacement Bracket for GA25GD 25G Guy Bracket Assembly
Made in the USA!
The ROHN GB25D is a single bracket, (1) out of (3) used that comprises a complete GA25GD Assembly (Not included) that Mounts to the ROHN 25G Series Guyed Towers at any Horizontal Brace. This Single Bracket (1 per Order) is an approximately 1.5" inches wide by 0.25" inch thick formed Bar for Repair and Replacement of your existing GA25GD Guy Bracket Assembly.
Order Does Not include any replacement Hardware

ROHN ACWS Anti-Climb Warning Sign "Do Not Climb" for All Towers
Made in the USA!
This ROHN ACWS Anti Climb Warning Sign Kit is an OEM product from the ROHN Factory for placement on new tower installations and replacement on existing tower sites where the sign and sticker have faded due to exposure. Public Notice of "Do Not Climb" my Tower. One of the items on your yearly checklist.

ROHN AS25G Antenna Rotor Accessory Shelf with Hardware for 25G Tower Sections
Made in the USA!
The ROHN AS25G is an Accessory Shelf for mounting Antenna Mast Rotators, Beacon Lights and other Custom Uses. Drilled to fit the Hygain and Yaesu rotator bolt patterns, the accessory shelf plate is not drilled nor is it designed for use with thrust bearings. Field Drilling may be necessary to accommodate Specific Items beyond the two models indicated. The AS25G is Hot Dip Galvanized Steel with (3) U-Bolts to attach to all 3 Side Rails anywhere on a 25G Tower Section, usually somewhere below the Thrust Bearing Mount as the Shelf nor the Rotator is designed to take the load of the Mast and Antenna. In addition, the AS25G can be Mounted with Beacon Lighting anywhere needed along the 3 Side Rails of any 25G Tower Sections.

ROHN APL25G Assembly Finishing Plate and Beacon/Lightning Rod Mount on 25G Tower
Made in the USA!
This ROHN APL25G Assembly Plate is a Finishing Top Cap that is also used for Mounting Beacon Lighting, Cameras or a Lightning Rod onto the final section of a 25G Tower. The APL25G Assembly Plate Bolts onto the top of a regular ROHN 25G Standard Main Tower Section (hardware included). Field Drilling may be necessary for mounting Beacons, Lighting, Cameras or other Accessories onto the Plate itself with hardware that should be sourced with the Accessory in question.
A Hole is already provided for mounting a LRCL Lightning Rod that comes with its own mounting hardware (only 1 needed, available separately).

ROHN BAS25G Thrust Bearing Plate and Rotor Accessory Shelf Combo Top Cap for 25G Tower
Made in the USA!
This ROHN BAS25G Thrust Bearing Plate and Rotor Accessory Shelf Combo Top Cap Bolts onto the Top of Standard ROHN 25G Main Tower Section of 10, 7, 5 and 3 foot for Mounting both the Antenna Rotor (Hygain and Yaesu rotator bolt patterns) and the ROHN TB3 or TB4 Thrust Bearing on one Assembly, each with their own Shelf, with a plate to plate distance of 16 inches. Integral Ears also provide for Down Guys with Shackles and Thimbles.(Not Included)

ROHN AS25GTB Thrust Bearing Accessory Shelf with Hardware for 25G Tower Sections
Made in the USA!
The ROHN AS25GTB is used for Mounting a Thrust Bearing to a 25G Tower Section to suspend the weight and Wind Load of a Mast and Antenna off of the Antenna Rotor that would be mounted below. Drilled to fit the TB3 and TB4 bolt patterns, the plate is not drilled for, nor is it designed for use with an Antenna Rotator. The AS25G is Hot Dip Galvanized Steel with (3) U-Bolts to attach to all 3 Side Rails anywhere on a 25G Tower Section, usually somewhere above the Antenna Rotor Mount. In addition, the AS25G can be Mounted with Beacon Lighting anywhere needed along the 3 Side Rails of any 25G Tower Sections. Field Drilling may be necessary to accommodate the other aftermarket versions of Thrust Bearings so please verify and compare the bolt hole patterns. This AS25GTB Accessory Shelf can also be field drilled to accommodate the mounting of Beacon Lights and other Attachments.

ROHN 25JBK Replacement Bolt Kit for 25G Tower Sections
Made in the USA!
These ROHN 25JBK Bolts and Nuts are Hot Dip Galvanized like the Tower Section itself. Lasts Longer than the zinc plated versions. The Perfect Replacement Bolt Kit for high corrosion environments. This is the Exact same Bolt Kit contents you get inside the leg of each ROHN 25G Tower Main Section.
Factory OEM Product to the exacting specifications and Bolt Grades to assure Safety, Longevity and Reliability.

ROHN 25AJBK Replacement Bolt Kit for 25AG Series Tower Top Cap Sections
Made in the USA!
The ROHN 25AJBK is a Replacement Bolt Kit as would be Supplied with a New 20BG 25AG 25AG3 25AG5 Tower Section. Hot Dip Galvanized Grade 5 bolts with nuts to join the section and also includes the (2) Zinc Plated Set Screw Lug and Bolts Specifically for the 20BG, 25AG, 25AG3 and 25AG5 Top Cap Sections with Set Screw Mast Tubes
Factory OEM Product to the exacting specifications and Bolt Grades to assure Safety, Longevity and Reliability.