Towers | Poles | Mounts | Masts | Hardware | Guy | Cable | Wire | Carts | Racks | Tools
Your Cart
ProductQtyPrice
ROHN H50 Telescopi...1$129.95
Goods Total1$129.95
View Cart Check out
Printer View Tell a Friend

Rohn 9H50 Telescopic Antenna Push Up TV & Wireless Internet Antenna Mast - UPS Shippable

Price$139.95
Manufacturer Code9H50
Stock Level: 0
AvailabilityDiscontinued
ShippingCan ship anywhere

Highlights

Use As Guyed
   or Bracketed
Guy Rings Rotate
Five Guy Holes/ Ring
Masts have hardware
34 Feet Total Extended


Bulk Quantities Available Here!

ROHN 9H50 34 Foot Telescopic TV Wireless Antenna Push Up Mast

Made in the USA!Made in the USA!

This Special ROHN Factory Limited Edition Run of the H50 (5) section Mast scaled down to Ship at 99 inches via UPS Brown Truck (Ground) to Commercial and Residential addresses alike, and is designed to support light duty antennas in various applications to 34.34 feet in actual height. Used for Mounting Off-Air TV, Ham Radio, MMDS and Wireless Internet Antennas (not included). Get your Telescopic TV Antenna Mast delivered to your Home in the same UPS Brown Truck you see every day. Installers for SMATV, WIFI, Wireless Internet and Telemetry will love this Mast when it fits in the elevator (99 and 1/4 inch collapsed of the Commercial Building it's being Installed in. The Managers will love the Cost Savingsof a single Drop Shipment when compared to Truck Freight for the Normal 10 foot versions. All Telescoping push-up Masts are galvanized and come with hardware. The unique Rohn design features interior tube flanging combined with a double crimped exterior tube to produce a stronger and more stable joint than most common mast. Each section extends deeper into the lower tubes than most designs, adding to the masts stability.

Mast  Section Dimensions are:


(1) 8' 2.25" length x 1.25" O.D. (16 AWG)
(2) 7' 10.5" length x 1.50" O.D. (18 AWG)
(3) 7' 04.5" length x 1.75" O.D. (18 AWG)
(4) 6' 10.5" length x 2.00" O.D. (18 AWG)
(5) 6' 04.5" length x 2.25" O.D. (18 AWG)
Compare to Channel Master 1620, 1630, 1640, 1650, 1820, 1830, 1840, 1850 Telescopic Masts!
This Item Ships UPS Brown!


Note

Installation Guidelines:

  1. Installation or dismantling of telescoping masts require professional contractors experienced with guyed masts.
  2. All installations must be bracketed or guyed.
  3. The pictured guy wire kit layouts are for a typical installation. Individual installation requirements may vary.
  4. Antenna load (top load) should not exceed an effective projected area (EPA) of 2 square feet (see your antenna specifications).
Specification Sheet
Spec Sheet:
Installation Sheet:
Rate this product.
Product isn't rated yet. Write a review.

Remember those older AM/FM Portable Radios with the antenna that you extended by pulling it out? Or the Radio Antennas on older cars that would pop- out, extend and retract when you turned on the radio? This Mast isn't an Antenna, but it extends and retracts by hand in similar fashion. Available in 20', 30', 40' and 50' heights. All ROHN telescoping masts are pre-galvanized and come assembled with hardware. Erection is made by simply connecting guys and brackets to the attached unique heavy duty rolled edge guy rings and clamps, extend each section one at a time (starting with the innermost section), insert the locking cotter pins, rotating the tubes to a locked position, and tightening the clamps. Repeat the process on each successive section until fully erect.

The unique ROHN Products design features interior tube flanging combined with a double crimped exterior tube to produce a stronger and more stable joint than most common masts. This design exclusive also prevents the sections from accidentally pulling apart and allows disassembly by pulling each section out through the lower end.
Each section extends deeper in to the lower tubes than most other designs, adding still further to the stability of the structure.

H Series
This heavy duty series uses 1-1/4" 16 gauge galvanized tubing for top section. All other sections are 18 gauge.

Assembly
1. Secure base and anchors (sold separately).
2. Attach lowered mast to base.
3. Secure guy lines to the lower Guy Ring and attach to anchors. Align the mast vertically by tightening the Guy Lines.
4. Secure upper Guy Ring using the appropriate Mast Clamp to desired location on the upper Tube (see note 8 on page 10).
5. Secure appropriate length guy lines to the upper Guy Ring and let them hang.
6. Raise the upper Tube and inset the cotter pin. Make sure that the cotter pin is inside the notch in the inside tube.
7. Secure the cotter pin and tighten the mast clamp.
8. Secure appropriate length guy lines to the next highest Guy Ring, and let them hang.
9. Raise the next smallest Tube and insert the cotter pin. Make sure that the cotter pin is inside the notch in the inside tube.
10. Secure the cotter pin and tighten the mast clamp.
11. Repeat steps 8-10 until all sections have been raised and are secured.
12. Attach all hanging Guy Lines to their respective anchor. Align the mast vertically by tightening the Guy Lines. Make sure to work your way up the mast while tightening.


ROHN Telescoping Masts



ROHN H-Series Masts


Get Adobe Reader



This Buyers Guide has will answer many questions you may have on this Product Line. For more detailed information and Specification Sheets covering many aspects of Various Parts, Accessories and Installation Scenarios... Please refer to the "Telescopic Mast" Link appearing in the Footer of this Page Below!

Telescoping Masts are not recommended for commercial, CB or beam antenna installations.