Towers | Poles | Mounts | Masts | Hardware | Guy | Cable | Wire | Carts | Racks | Tools
Your Cart
ProductQtyPrice
ROHN 25G Tower...1$260.00
Goods Total1$260.00
View Cart Check out
Printer View Tell a Friend

ROHN 25G Tower Face Dish Mount (2" I.D) (2-3/8" O.D.) - DM25G2

Price$290.00
Manufacturer CodeDM25G2
Qty
AvailabilityUsually ships in 24 Hrs
ShippingCan ship only within USA

Highlights

Hot Dip Galvanized
2 Plate accessory
Fits to 25G Main Section
 Accomodates:
2 inch STD (2-3/8 DIA) Pipe
(Included)

Bulk Quantities Available Here!

ROHN DM25G2 Tower Face Dish Mount
Face Mount includes 2 Angled Steel Cross-Members that Bolt directly to any of the 3 Faces of a Standard 25G Tower Section. 5 Foot x 2 inch STD (2-3/8 inch O.D.) Pipe connects with U-bolts to 25G Tower Section Brackets.

 

This Kit Includes
DM25G2
QUANTITY PART NUMBER DESCRIPTION DRAWING NUMBER
2 KY1550 Dish Mount Bracket B881437
1 KH275 2" STD x 5' Mounting Pipe B770160
2 KY1549 Mounting Clip Angle B881436
4 210018GA 1/2 x 1 1/2" Bolt Assembly C770404
8 JR66A 3/8" U-Bolt Assembly B651028
4 JR61A 3/8" U-Bolt Assembly B651028

 

ATTENTION:

A ROHN TA25 Tower Torque Arm Stabilizer Assembly is recommended in the immediate vicinity of this Mount. The 25G Tower can be used in guyed, self-supporting or bracketed configurations according to specifications in the ROHN Tower catalog. Consult ROHN Catalog Links at Footer Section below for ROHN 25G Tower Details.

 

spec. sheet

 

 

Spec. Sheet


Get Adobe Reader

 

 

 

 


ROHN DM25G2 mount goes together quickly, with a minimum of bolted connections. The angle steel cross members connect directly to the tower legs with easy-to-use u-bolts. This mount is hot dip galvanized . American Steel... Buy ROHN, Buy American.

 

 

 

 

Rate this product.
Product isn't rated yet. Write a review.

It is Important to choose an Antenna Mount and Wall Mounting Location with a Picture of the Finished Antenna Installation in Mind. Be Sure to First select a location that lends itself to applying a Vertical, Cantilevered, Twisting Load without Compromising the Integrity of the Wall Material you affix to. Most Modern Exterior Decorative Wall Finishes most often do not have the Strength to Hold the Weight and Pressure of a Large TV Antenna under Wind Load without fail. Beams and Studs within the Wall are an Absolute Must to Locate when the Wall Composition is anything other than Solid wood or Concrete. Attach to these Strength Members. Further, Think about what's underneath the Wall exterior. Is it stronger, will it yield to Pressure over time as well? Sandwich additional Material (wood or steel) to the backside or both sides of the wall at the points where the mount attaches, as to distribute the load on relatively weak wall materials and to dampen vibration from Wind. Weather Proof the Installation to Maintain the Integrity of your Home. Next consider the Location over a Lifetime of Adjustments, does it lend itself to modifications in Height or Direction? Larger Antennas increase the surface area presented to air movement, Hence, Wind-load does increase. As the length of the mast increases from Its last attached point on the structure, the torque applied also increases with Weight and Wind-Load, requiring a more substantive attachment and Load-Bearing material. Keep the Distance Minimal from the Antenna to the TV's and Equipment you feed, as to minimize loss and the need for Amplification. Further, the NEC (National Electrical Code partly defines a good Ground connection as being as short as possible, you must affix a connection to a good Earth Ground prior to Premise entry or Bond to an existing one.