Towers | Poles | Mounts | Masts | Hardware | Guy | Cable | Wire | Carts | Racks | Tools
Your Cart
ProductQtyPrice
ROHN 45G Top...1$398.00
Goods Total1$398.00
View Cart Check out
Printer View Tell a Friend

ROHN 45G Top Cap Tower Section R-45AG

× ROHN 45G Top Cap Tower Section R-45AG was added to your Shopping Cart.
Price$398.00
Manufacturer Code45AG
Qty
AvailabilityUsually ships in 24 Hrs
ShippingCan ship only within USA

Highlights

Hot Dip Galvanized
Double Bolted Joints
Zig-Zag Rod Bracing
1-1/4" Steel Tubing
Side Rails
16 3/4" Equalateral
Triangular Design
Can be used in:
Guyed Self Supporting
Bracketed Config.s

Bulk Quantities Available Here!

ROHN 45AG 9 Foot (2.00 inch Outside Diameter) Tower Top Cap Section
consists of 14 gauge walls with 4 bays of bracing and swaged, double-bolted connections. The Pinnacle of this Section is Capped with a 16 AWG Tube (2.00 inches O.D./1.87 inches I.D.), protruding 12 inches above apex of side rails. This Rohn section is one that can be used to top off the 45G tower. The 45AG is available in the standard 9 foot section length. This tower uses double bolted joints which are proven to be the best method of joining tower sections for sturdiness and dependability. Featuring a 16 3/4 inch equilateral triangular design, the 45AG is constructed of extra heavy duty 1-1/4" steel tubing side rails with continuous solid steel rod bracing. Each 9' section is shipped containing all required nuts and bolts attached to one leg. The 45G tower can be used guyed, self-supporting or bracketed configurations according to specifications in the ROHN catalog. As a guyed structure, it can rise to a maximum of 300 feet. Consult ROHN Catalog Links at Footer Section below for ROHN 45G Tower Details.

spec. sheet



Spec. Sheet


Get Adobe Reader

 

 

 

 


The 2.00 inch Outside Diameter Mast Tube at the Pinnacle of the Rohn 45AG Top Cap Section means approx. 1-13/16 inch Inside Diameter. Both Top and Bottom end of the Tube is free of attachments, but can have the ROHN TB50 (1.25 inch Inside Diameter) or TB75 (1.50 inch Inside Diameter) peened in to float in and complete your 1.25 inch Outside Diameter or 1.50 inch Outside Diameter Antenna Mast installation onto the R-25AG. Refer to the "25G Tower Accessories" Category for these Parts.
This Item Ships LTL Freight ONLY...
Click Here for: What You Want to Know about Shipping!

 

 

 

 

Rate this product.
Product isn't rated yet. Write a review.

Since there are various other Manufacturers of Towers and Tower accessories that copy the ROHN Tower design, if you are not sure of the manufacturer of your Tower, you can at least compare the actual measurements and design of yours to those found in the spec. sheets in the ROHN catalog section via the Link provided above to assure yourself that additional sections or parts will fit. We cannot make that determination for you as the ROHN clones are something we don't carry or otherwise represent in our Product line. All towers in the GT Series are constructed with high strength steel tubing and feature ROHN's exclusive Zig-Zag ® solid rod bracing to provide exceptional strength. All GT Series Towers are hot dip galvanized after fabrication. In this process, each section of the tower is totally immersed in molten zinc, allowing every square inch of the tower, inside and out, to be completely covered. Hot dip galvanizing protects all points of welding and construction against rust and corrosion while providing an attractive finish.

The 45G is a true multi-use structure that provides excellent strength for applications up to 300´. It´s offered with either heavy steel tube legs to satisfy a wide variety of needs under varied conditions. When properly installed, the standard tower will support the loads shown on various guyed and self-supporting information sheets in the ROHN catalog.

Most Restrictions Allow for 45 feet of Height without the Necessity of Guy Wires, Anchors or Braces. However, No Tower is self supporting during construction! Always use temporary guys on the top most section, and install permanent guy wires as soon as a guy point height is reached.

Wind Loading, Antenna Loading and Wind Survivability ratings vs. Height Documentation Provided by ROHN is available here as a Resource, but is by no means complete by itself or a susbstitution for Engineering Conducted Specific to your Application. Contact Us with any Questions you may have regarding Use prior to Purchase. All Information regarding the ROHN 45G Tower line, Parts and Accessories is as accurate and complete as we can possibly provide given that this Resource Offering is subject to change without Notice and is beyond Our Control.


ROHN 45G Buyers Guide


ROHN 45G Buyers Guide


Get Adobe Reader



This Buyers Guide will answer many questions you may have on this Product Line. For more detailed information and Specification Sheets covering many aspects of Various Parts, Accessories and Installation Scenarios... Please refer to the "ROHN 45G Tower" Link appearing in the Footer of this Page Below!

Products   Recently Viewed