Printer Friendly Tell a Friend

18 inch Telescopic TV Antenna Mast Wall Mount Bracket

Highlights
Galvanized Finish
18 inch Clearance
Adjustable 1.25 to 3 inch DIA
3rd Support Leg
Wall Mount for:
   ROHN H30, H40, H50 and Channel Master 1620, 1630, 1640, 1650, 1820, 1830, 1840, 1850
Price$24.95
Manufacturer CodeEZ 30-18W
Qty
AvailabilityUsually ships in 24 Hrs
ShippingCan ship anywhere
EZ 30-18W Telescopic TV Antenna Mast 18" Wall Mount Bracket
Made in the USA!Made in the USA!
is designed to Wall Mount Support ROHN H50, H40, H30, H20 Channel Master 1620, 1630, 1640, 1650, 1820, 1830, 1840, 1850 Telescopic Masts. Adjustable for Clamping ANY HDTV Antenna Masts from 1.25 to 3 inches in Diameter. Guy Wire Support for Mast Sections above this mount will still be required. This Bracket will Stand off any Antenna Mast within this Diameter range, but is NOT designed to support the weight and load of any Telescopic Antenna Mast off of the Ground. The Pre-Drilled Set Screw Hole Allows Installer to Install a Customer Provided Set Screw and Mast that Together, Siezes the Mast from Twisting due to Antenna Load, assuring the Antenna remains on Target. Bonding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance. (Mast not included).
Compare to ROHN R-WM18S and R-WM18D

NoteThis "Y" Antenna Mast Wall Mount Bracket with 3rd Leg Support is Designed for Wall Mount Support of Antenna Masts of all Diameters from 1 inch to 4 inches with 18 inches of clearance from the Wall with the added reinforcement of a 3rd leg that goes to transfer the weight load leverage to the wall, but not the weight of a Telescopic Antenna Mast or ANY Mast greater than 10 Feet in Height (Depending on Antenna size!) off of the Ground and on the Wall alone. Use a Ground Plate like EZ32A or GTMBL to mount the Bottom of a Telescopic Antenna Mast from the ground up, with the Wall Bracket maintaining vertical alignment and clearance from the Wall to pass Roof edge. These Mounts do not replace or otherwize reduce the need for proper guying of the Telescopic Antenna Masts. As with all Masts, Guy wire support and Grounding are Critical to Antenna Survival.
Specification Sheet






EZ46-3PO Pitch Pad Moisture Barrier Kit - $1.60
EZ 46-3PO Pitch Pad Only Kit
Made in the USA!Made in the USA!
Comes with ( 3 Pitch Pads 3" x 1.5" only) for Weather-Proofing Bracket Mounting Installations on Exterior Surfaces...

read more...
Satellite TV Antenna Combination Mast 5 foot by 1.66" and 2" OD - $12.95
3 Star 5994 1.66 and 2 Inch O.D. Combination Satellite and Off-Air TV Antenna Mast
(56-3/4" Length) by 1.66" and 2.00 " O.D. 16 AWG Galvanized Antenna Mast (Mount Not Included)...

read more...
Satellite Dish Antenna Ground Pole Mast 6 foot by 2.00" OD - $12.95
3 Star 5999 6 Foot 2.00 O.D. Steel Satellite Dish Ground Pole Mast
Ideal as a Super DISH and Wild Blue Dish Antenna Mast for Ground or Wall mount Installation (Mount Not Included)...

read more...
Product isn't rated yet. Write a review.

Wall Mounts

Wall & Eave Mount Brackets for Satellite TV Antenna Mast, Cellular Wireless Internet, Business Band and Telescopic Antenna MastsIt is Important to choose an Antenna Mount and Wall Mounting Location with a Picture of the Finished Antenna Installation in Mind. Be Sure to First select a location that lends itself to applying a Vertical, Cantilevered, Twisting Load without Compromising the Integrity of the Wall Material you affix to. Most Modern Exterior Decorative Wall Finishes most often do not have the Strength to Hold the Weight and Pressure of a Large TV Antenna under Wind Load without fail. Beams and Studs within the Wall are an Absolute Must to Locate when the Wall Composition is anything other than Solid wood or Concrete. Attach to these Strength Members. Further, Think about what's underneath the Wall exterior. Is it stronger, will it yield to Pressure over time as well? Sandwich additional Material (wood or steel) to the backside or both sides of the wall at the points where the mount attaches, as to distribute the load on relatively weak wall materials and to dampen vibration from Wind. Weather Proof the Installation to Maintain the Integrity of your Home. Next consider the Location over a Lifetime of Adjustments, does it lend itself to modifications in Height or Direction? Larger Antennas increase the surface area presented to air movement, Hence, Wind-load does increase. As the length of the mast increases from Its last attached point on the structure, the torque applied also increases with Weight and Wind-Load, requiring a more substantive attachment and Load-Bearing material. Keep the Distance Minimal from the Antenna to the TV's and Equipment you feed, as to minimize loss and the need for Amplification. Further, the NEC (National Electrical Code partly defines a good Ground connection as being as short as possible, you must affix a connection to a good Earth Ground prior to Premise entry or Bond to an existing one.

Wall Mounts
Antenna Wall Mounts and Brackets
Wall & Eave Mount Brackets for Satellite TV Antenna Mast, Cellular Wireless Internet, Business Band and Telescopic Antenna MastsIt is Important to choose an Antenna Mount and Wall Mounting Location with a Picture of the Finished Antenna Installation in Mind. Be Sure to First select a location that lends itself to applying a Vertical, Cantilevered, Twisting Load without Compromising the Integrity of the Wall Material you affix to. Most Modern Exterior Decorative Wall Finishes most often do not have the Strength to Hold the Weight and Pressure of a Large TV Antenna under Wind Load without fail. Beams and Studs within the Wall are an Absolute Must to Locate when the Wall Composition is anything other than Solid wood or Concrete. Attach to these Strength Members. Further, Think about what's underneath the Wall exterior. Is it stronger, will it yield to Pressure over time as well? Sandwich additional Material (wood or steel) to the backside or both sides of the wall at the points where the mount attaches, as to distribute the load on relatively weak wall materials and to dampen vibration from Wind. Weather Proof the Installation to Maintain the Integrity of your Home. Next consider the Location over a Lifetime of Adjustments, does it lend itself to modifications in Height or Direction? Larger Antennas increase the surface area presented to air movement, Hence, Wind-load does increase. As the length of the mast increases from Its last attached point on the structure, the torque applied also increases with Weight and Wind-Load, requiring a more substantive attachment and Load-Bearing material. Keep the Distance Minimal from the Antenna to the TV's and Equipment you feed, as to minimize loss and the need for Amplification. Further, the NEC (National Electrical Code partly defines a good Ground connection as being as short as possible, you must affix a connection to a good Earth Ground prior to Premise entry or Bond to an existing one.
Products   Recently Viewed

18 inch Telescopic TV Antenna Mast Wall Mount Bracket

Telescopic TV Antenna Mast 18" Wall Mount Bracket
Price$24.95
EZ 30-18W Telescopic TV Antenna Mast 18" Wall Mount Bracket
Made in the USA!Made in the USA!
is designed for Wall Mount Support of ROHN H50, H40, H30, H20 and Channel Master 1620, 1630, 1640, 1650, 1820, 1830, 1840, 1850 Telescopic Push Up TV Antenna Masts or ANY Mast from 1.25 to 3 inches in Diameter (Mast not included). Guy Wire Support for Mast Sections above this mount will still be required...

Your Cart
Credit Cards Taken
Your shopping cart is empty!
Customer Service
Call Us AT 1-877-660-0974
Locations
2 Great Locations


Two Great Locations!
Ashland, VA

and

Orlando, FL...
Orders to these States are taxed

We Ship Fast!
Your Orders leave Daily! UPS... What can Brown do for You?!United States Postal ServiceR+L Carriers... Value Added Advantages!