Towers | Poles | Mounts | Masts | Hardware | Guy | Cable | Wire | Carts | Racks | Tools
Your Cart
Your shopping cart is empty!

Categories

Printer View Tell a Friend

HOLLAND 1 GHz Power Passing 4-way Cable TV Antenna Splitter

Price$4.60
Manufacturer CodeGHS-4P
Qty
AvailabilityUsually ships in 24 Hrs
ShippingCan ship Canada

Highlights

5-1000 MHz. Bandwidth

45 dB port-to-port isolation*

35 dB output return loss*

Low intermodulation design

Double-Thick Plating

Enhanced Sub Band Performance

Power Pass One Port

6 kV Survivability

100% soldered backplate

Flat End F-ports

*(Return Band)

Bulk Quantities Available Here!

HOLLAND GHS-4P 4-way 1 GHz. Power Passing Cable TV Antenna Splitter.
The GHS Series 1 GHz Splitters are state-of-the-art product lines designed and tested using the most current procedures. New performance features have been incorporated to make both series compatible with the latest digital and return path requirements.
Low intermodulation design and optimized return band prevents high cable modem signals from affecting forward band transmission. The GHS-4P Series power passing to one port splitters have been specifically designed to meet the highest electrical specifications. Careful isolation of the RF and DC path is required to prevent saturation or burn-out of the high permeability ferrite core. This has been accomplished using a separate DC bypass core material which can withstand higher impulse spikes before saturating.

spec. sheet



Spec. Sheet


Get Adobe Reader




There are few Power Passing 4-way Coaxial Cable Splitters on the Market, and This One passes Power only on 1 Leg only off the Split. That way, you can back-feed power upstream to the HDTV Antenna Pre-Amplifier or the Cable TV In-Line Amplifier without sending Voltage throughout the entire system. Its Double Thick Plated Housing is Soldered Closed and Sealed from the Environment, as well as Transient and Spike Voltage Resistant. There's been plenty of chatter about this Product on Technical Blog Sites, this is where you get it. Get the Specifications by Clicking on the pdf Link above. It will pass Forward and Return signals; making it perfect for Splitting Cable TV with High-Speed Internet Connection Signals. The Voltage Protection also makes it suitable for splitting HD TV Antenna Signals as well. The Flat "F" Connector ends means that the connection to the RG coaxial cable you use (RG-6 or RG-11) is solid, secure and doesn't slip or back off after tightened with appropriate force (most Coaxial Cable Manufacturers specify in inch/pounds). When making RG-6 or RG-11 cable connections outside, a weather boot covering and some sort of Silicone compound are highly recommended.

4-Way Splitters are typically the Part you would use to take One (1) cable Feed and "Split" it into Four (4) in order to Provide Signal to 4 Independant Devices, or Three More Cables to complete the Run(s) to their Final Destination(s). Please be Sure to Select the Appropriate Splitter not just By Manufacturer and Price. But Rather, Consider the Specifics of Bandwidth, Packaging (Indoor vs. Outdoor), Loss, Powering Requirements Up/Down-Stream and the Overall Needs of the Final System You Wish to Create...

If you are adding a splitter to an existing Cable TV or Antenna feed, you may need to compensate for the loss that you are about to introduce. The gain of a Line Amplifier should be selected to zero out the loss that follows it. In other words, if you have fifty feet of cable and a two-way splitter, then a 10 db amplifier will be fine. Conversely, if you have an eight-way splitter and hundreds of feet of cable, you will need an amplifier with a higher gain. Just as in the case of a Pre-Amplifier, however, bigger is not always better.

Commensurate with Coaxial Cable TV Antenna Splitter Installation, you want to Ground your Cable TV or HDTV Antenna Coaxial Cable System Outside before bringing the TV Cable Inside. This way, Lightning Strikes and Power Surges have an opportunity to arrest before reaching your TV and Entertainment Electronics. The Integral Grounding Block designed onto every Outdoor Use Compatible RF Signal Splitter we sell will effectively convey this unwanted Electrical Energy to a Ground Rod via a Copper Ground Wire that you Install (not included). Consult your Local Building Code and NEC for guidance to Properly Grounding your HD TV Antenna, Cable TV, WI-FI, Wireless Internet, Business Band, CB or Amateur Radio Antenna Installation.