Towers | Poles | Mounts | Masts | Hardware | Guy | Cable | Wire | Carts | Racks | Tools
Your Cart
Your shopping cart is empty!

Categories

Printer View Tell a Friend

REGAL 3-Way Vertical Splitter 5-1000 MHz. -W- Ground

Price$3.60
Manufacturer CodeDS3DGV10
Stock Level: 93
Qty
AvailabilityUsually ships in 24 Hrs

Highlights

    Specifications

Bandwidth  5-1000MHz

Insertion -4.5/8.2dB max.

Isolation      -20dB min

Return Loss -15dB min

Nickel Plated Housing

Epoxy of Rear cover

120dB RFI shield.

Bulk Quantities Available Here!

Regal DS3DGV10 3-Way Vert. Splitter 5-1000 MHz. with Ground.
Mechanical integrity ensures EMI isolation, maximum contact area, long-term identification, and breakage resistance. A Conical Seizure Mechanism provides for improved return loss and isolation specifications. A Printed Circuit Board ensures consistent RF performance and high port isolation. One Low-Loss Output (-3.5 dB, -4.5 dB max.) and Two Low-Loss Output (-7.0 dB, -8.2 dB max.) Ports for different drop length applications.

This is one of those splitters you would find or use inside of those steel lock-boxes on the side of an Apartment complex, or the little gray box on the side of your Home or Office that the Cable TV company installed. It features Vertical Port "F" connections. Its typically Vertically Mounted inside of these little boxes because it's easier to connect/disconnect the cables when all the "F" connection Ports are facing in the same direction. So when you are mounting a 3-way splitter in a tight space without a lot of room around it for the RG-6 Coaxial Cable to make connection, this is the one you want! It will pass Forward and Return signals; making it perfect for Splitting Cable TV with High-Speed Internet Connection Signals. The Voltage Protection also makes it suitable for splitting HD TV Antenna Signals as well. The Flat "F" Connector ends means that the connection to the RG coaxial cable you use (RG-6 or RG-11) is solid, secure and doesn't slip or back off after tightened with appropriate force (most Coaxial Cable Manufacturers specify in inch/pounds).

3-Way Splitters are typically the Part you would use to take One (1) cable Feed and "Split" it into Three (3) in order to Provide Signal to 3 Independant Devices, or Two More Cables to complete the Run(s) to their Final Destination(s). Please be Sure to Select the Appropriate Splitter not just By Manufacturer and Price. But Rather, Consider the Specifics of Bandwidth, Packaging (Indoor vs. Outdoor), Loss, Powering Requirements Up/Down-Stream and the Overall Needs of the Final System You Wish to Create...

If you are adding a splitter to an existing Cable TV or Antenna feed, you may need to compensate for the loss that you are about to introduce. The gain of a Line Amplifier should be selected to zero out the loss that follows it. In other words, if you have fifty feet of cable and a two-way splitter, then a 10 db amplifier will be fine. Conversely, if you have an eight-way splitter and hundreds of feet of cable, you will need an amplifier with a higher gain. Just as in the case of a Pre-Amplifier, however, bigger is not always better.

Commensurate with Coaxial Cable TV Antenna Splitter Installation, you want to Ground your Cable TV or HDTV Antenna Coaxial Cable System Outside before bringing the TV Cable Inside. This way, Lightning Strikes and Power Surges have an opportunity to arrest before reaching your TV and Entertainment Electronics. The Integral Grounding Block designed onto every Outdoor Use Compatible RF Signal Splitter we sell will effectively convey this unwanted Electrical Energy to a Ground Rod via a Copper Ground Wire that you Install (not included). Consult your Local Building Code and NEC for guidance to Properly Grounding your HD TV Antenna, Cable TV, WI-FI, Wireless Internet, Business Band, CB or Amateur Radio Antenna Installation.

Products   Recently Viewed