|
|
 |
20 Foot Telescopic Push-Up Antenna Mast EZ TM-20 |
|
|
|
Easy Up EZ TM-20 20 foot Telescoping Mast
2 section 18 gauge Mast collapses down to 10 Feet in length that with overlapping, extended mast length is 19'-3", Used for Mounting Off-Air TV, Ham Radio, MMDS and Wireless Internet Antennas (not included) MIN ORDER-25 Pieces...
This Item Ships LTL Freight ONLY...
Has a very hardy thumbscrew/collar system for setting height, Best we've seen to date.
Availability:
Usually ships in 1 week
Shipping:
Can ship only within USA
Manufacturer Drop-Ship is subject to a Convenience Fee
|
EZ32A Telescopic Antenna Mast Heavy Duty Ground Plate
- $21.95
Easy Up EZ32A Heavy Duty Telescopic Mast Ground Mount
is designed to support and facilitate grounding for ROHN H20, H30, H40, H50 and Channel Master 1620, 1630, 1640, 1650, 1820, 1830, 1840, 1850 Telescopic (Push-up) Antenna Masts. Outer dimensions are 9 x 9 inches...
Shipping/ More Info Here
|
Roof Base Mount for Telescopic Antenna Mast
- $19.95
EasyUp 19B Universal Telescopic Push Up Antenna Mast Roof Base Mount
is completely assembled for Flat or Peaked Roof Mounting ROHN H20, H30, H40, H50 and Channel Master 1620, 1630, 1640, 1650, 1820, 1830, 1840, 1850 Telescopic Push Up Antenna Masts from 1-3/4 to 2-5/8 inches in DIA...
Shipping/ More Info Here
|
20 Foot Telescopic Antenna Mast 3 Way Down Guy Wire Kit
- $114.95
ROHN H203WAYGUY Telescopic Antenna Mast Down Guy Wire and Anchor Kit
is designed to Securely 3 way Guy at 2 levels your ROHN H20 and Channel Master 1620, 1820 Telescopic Push Up Antenna Masts. Choose Guy wire gauge and Anchor size. Mast is not included...
Shipping/ More Info Here
|
20 Foot Telescopic Antenna Mast 4 Way Down Guy Wire Kit
- $159.95
ROHN H204WAYGUY Telescopic Antenna Mast Down Guy Wire and Anchor Kit
is designed to Securely 4 way Guy at 2 levels your ROHN H20 and Channel Master 1620, 1820 Telescopic Push Up Antenna Masts. Choose Guy Wire gauge and Anchor size. Mast is not included...
Shipping/ More Info Here
|
|
|
|
|
|
|
Remember those older AM/FM Portable Radios with the antenna that you extended by pulling it out? Or the ;Radio Antennas on older cars that would pop- out, extend and retract when you turned on the radio? This Mast isn't an Antenna, but it extends and retracts by hand ;in similar fashion. ;Available in 20', 30', 40' and 50' heights. All ROHN telescoping masts are pre-galvanized and come assembled with hardware. Erection is made by simply connecting guys and brackets to the attached unique heavy duty rolled edge guy rings and clamps, extend ;each section one at a time (starting with the innermost section), insert the locking cotter pins, rotating the tubes to a locked position, and tightening the clamps. Repeat the process on each successive section until fully erect.
The unique ROHN Products design features interior tube flanging combined with a double crimped exterior tube to produce a stronger and more stable joint than most common masts. This design exclusive also prevents the sections from accidentally pulling apart and allows disassembly by pulling each section out through the lower end.
Each section extends deeper in to the lower tubes than most other designs, adding still further to the stability of the structure.
H Series
This heavy duty series uses 1-1/4" 16 gauge galvanized tubing for top section. All other sections are 18 gauge.
Assembly
1. Secure base and anchors (sold separately).
2. Attach lowered mast to base.
3. Secure guy lines to the lower Guy Ring and attach to anchors. Align the mast vertically by tightening the Guy Lines.
4. Secure upper Guy Ring using the appropriate Mast Clamp to desired location on the upper Tube (see note 8 on page 10).
5. Secure appropriate length guy lines to the upper Guy Ring and let them hang.
6. Raise the upper Tube and inset the cotter pin. Make sure that the cotter pin is inside the notch in the inside tube.
7. Secure the cotter pin and tighten the mast clamp.
8. Secure appropriate length guy lines to the next highest Guy Ring, and let them hang.
9. Raise the next smallest Tube and insert the cotter pin. Make sure that the cotter pin is inside the notch in the inside tube.
10. Secure the cotter pin and tighten the mast clamp.
11. Repeat steps 8-10 until all sections have been raised and are secured.
12. Attach all hanging Guy Lines to their respective anchor. Align the mast vertically by tightening the Guy Lines. Make sure to work your way up the mast while tightening.
ROHN H-Series Masts
This Buyers Guide has will answer many questions you may have on this Product Line. For more detailed information and Specification Sheets covering many aspects of Various Parts, Accessories and Installation Scenarios... Please refer to the "Telescopic Mast" Link appearing in the Footer of this Page Below!
ROHN Tower series is the Workhorse of America's Large and Small Communications needs; from Governments, Institutions, Space Program, Olympics, TV AM FM Broadcast, Terrestrial Microwave to Business-Band Radio, HAM Radio Operators, to Off-Air Antenna TV and DTV Reception in Fringe areas outside the Surburban Broadcast Area. ROHN fabricates their towers from the highest quality steel. They maintain mill certification on the raw materials they receive to verify the material composition of each structural member. With a focus on quality, their fabrication facility has been awarded Certification by the American Institute of Steel Construction and the Canadian Welding Bureau. They have also been approved by the City of Los Angeles, CA and Clark County, NV as a certified fabricator. They are confident that their facility and staff can produce superior grade towers and poles that will meet your standards and weather the test of time. ROHN Towers, Accessories and their Construction/Assembly Assistance are also available via 3StarInc.com... Call 877-660-0974 at anytime for assistance.
|
|
|
|
|
|
|
|
|
Your shopping cart is empty!
|
|
|
