Easy Up EZ32C Base Plate for Telescopic Pole and Antenna Mast fits up to 2.25" OD
Easy Up
Made in the USA!
This Easy Up EZ32C Galvanized 9x9 inch 16 gauge Base Plate comes with a welded on 6 inch tall by 2.25" ID Mast Collar with single bolt Set Screw and a separate Pier Pin style Stake for Ground Level Elevation installation of Telescopic and ANY Antenna Mast Poles from 1.50 to 2.25 inch Outside Diameter in both Temporary and Permanent Base Mounting by placement upon a Gravel or Concrete Foundation with the Center Stake inserted into, and the Plate resting on top of, a (1) Foot Cubed bed of gravel or pad of Poured Concrete above surrounding soil elevation.(depending on soil and frost conditions)
Will Also Accommodate Telescopic Masts:
ROHN H20 H30 H40 H50 and Easy Up TM-20 TM-30 TM-40 TM-50
Manufacturers recommend that masts heights of 10 feet and higher above the uppermost bracket be guyed for Addition Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance
This Base Plate is THE Base Plate to use with ROHN H30, H40, H50 and Channel Master 1620, 1630, 1640, 1650, 1820, 1830, 1840, 1850 Telescopic (Push-up) Masts. All the other plates have a Rod or angle piece that the Tube of the Mast centers around loosely. This Plate has a collar with a Set Screw that securely holds the Telescopic Mast Tube in place and can be in turn, cemented into the concrete Pad via the Pin provided. The word "Ground" as used in the description can be a bit of a misnomer; it does not provide a "Earth Ground" in and of itself, but rather is a junction component that rests on the ground or pad and should be Bonded to with a proper Earth Ground composed of a 5/8 inch by 8 foot Copper Clad Ground Rod as a minimum. Consult your Local Building Code and NEC for guidance to Properly Grounding your HD TV, WI-FI, Wireless Internet, Business Band, CB or Amateur Radio Antenna Installation.
Telescopic Antenna Mast Hardware, Base Plates, Grounding and Accessories
3 Star Inc stocks replacement parts for ROHN and Easy-Up Brand Telescopic Antenna Mast parts including: collars, guy rings and clamps as well as supplemental parts to complete your installation.
3 Star Inc not only Stocks ROHN and Easy Up OEM Guy Rings and Clamps, We also offer Supplemental Guy Rings that can be installed on Any Telescopic Mast Section at any height, freeing you from the fixed position of the Factory Supplied Guy Rings.
Read more Category Items
In this Category We list every Base Plate for Telescopic Masts offered by the Manufacturers from simple flat plane plates, to hinged mounts with collars for Ground and Roof Installations on Pitched and Peak.
Herein you will find a limited offering of our Grounding and Lightning Protection parts including: Ground Wire, Clamps and Rods.
Ground Blocks and Proper Grounding are an Important, often overlooked, aspect of Your telescopic Antenna Mast Installation and Safety. Proper Grounding can also Reduce the Reception of Interfering RF Signals. Grounding of Masts, Antennas, Cable TV and other RF Distribution Systems are covered by the NEC. Grounding can be as simple as a 12 AWG Ground Wire connected a short distance away to a 8 foot 5/8" DIA Copper Ground Rod (not supplied) or Bonded to the Existing Power Ground by the Power Meter installed on the side of your Home or Office. However, most State and some Local codes will contain requirements that supersede that of the NEC. Please Refer to Your Local Building and Electrical Codes for Guidance.
We will Happily answer any questions you may have on this Product Line with more detailed information, Installation and Specification Sheets covering routine Installation Scenarios as available.
Contact Us or Call Us at 877-660-0974 at anytime with any Questions you may have regarding Use prior to Purchase.
Note:
Telescopic masts are not recommended for Commercial, CB or Beam antenna installations.
Antenna load (top load ) should not exceed an effective projected area ( EPA ) of 2 square feet
(see your antenna specifications)
