Our Aluminum Mast Poles come in 1.25", 1.50" and 2.00" OD, and lengths of 6, 8, 10 and 16 feet for use on Aluminum Towers as Pinnacle Masts, Residential and Commercial Installations of Wall and Roof mount Starlink Terminals and Scada Remote Telemetry.
Manufacturers recommend that mast heights of 10 feet and higher above the uppermost bracket, mount and/or preceding guy level be guyed at the uppermost level for Additional Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance.

We Stock Hot Dipped Galvanized Steel Pipe in 1-1/4", 1-7/8", 2-3/8" and 3-1/2" OD with 14 gauge and Schedule 40 wall thicknesses of 5, 7 and 10 foot lengths used on Communications Tower and Heavy Duty Wall Mounting for a variety of Cellular, PCS, Wireless Cable, Microwave, Wireless Internet, WiFi Hot Spots, DBS, MDS, MMDS and UHF/VHF Installations.
Hot Dip Galvanization provides a protective zinc coating that prevents rust and corrosion from water or moisture over time.

Professional Grade Telescopic Masts for TV, Wifi, Repeater, Gateway Antennas & Weather Sensors

We Stock the Highest Quality Telescopic Antenna Masts made from 18 and 16 AWG galvanized steel right here in the USA. These Masts are suitable for tons of applications where a fast an simple extension is needed. They have been used for everything from digital TV antenna applications to wireless communications to weather stations and even IoT Sensors. The masts can be used retracted or fully extended and anywhere in between. They can be supported and mounted against a structure, mounted on a roof or even guyed in the middle of a field. Our reliable and durable telescopic poles come in heights of 20, 30, 35, 40 and 50 FT and all have a engineered thumbscrew/collar system for setting height.

Manufacturers recommend that mast heights of 10 feet and higher above the uppermost bracket, mount and/or preceding guy level be guyed at the uppermost level for Additional Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance.

Telescopic Mast & Antenna Pole Down Guy Installation Material and Kits

We Stock Guy Wire, Earth Screw Anchors, Base Plates, Cable Clamps, Thimbles, Guy Guards, Gripples and Tensioning Tools separately and in 3-way or 4-way multi-level Guy Kits for 2, 3, 4 and 5 level Mast Installations.

Telescopic Antenna Mast Hardware, Base Plates, Grounding and Accessories

3 Star Inc stocks replacement parts for ROHN and Easy-Up Brand Telescopic Antenna Mast parts including: collars, guy rings and clamps as well as supplemental parts to complete your installation.

3 Star Inc not only Stocks ROHN and Easy Up OEM Guy Rings and Clamps, We also offer Supplemental Guy Rings that can be installed on Any Telescopic Mast Section at any height, freeing you from the fixed position of the Factory Supplied Guy Rings.

In this Category We list every Base Plate for Telescopic Masts offered by the Manufacturers from simple flat plane plates, to hinged mounts with collars for Ground and Roof Installations on Pitched and Peak.

Herein you will find a limited offering of our Grounding and Lightning Protection parts including: Ground Wire, Clamps and Rods.
Ground Blocks and Proper Grounding are an Important, often overlooked, aspect of Your telescopic Antenna Mast Installation and Safety. Proper Grounding can also Reduce the Reception of Interfering RF Signals. Grounding of Masts, Antennas, Cable TV and other RF Distribution Systems are covered by the NEC. Grounding can be as simple as a 12 AWG Ground Wire connected a short distance away to a 8 foot 5/8" DIA Copper Ground Rod (not supplied) or Bonded to the Existing Power Ground by the Power Meter installed on the side of your Home or Office. However, most State and some Local codes will contain requirements that supersede that of the NEC. Please Refer to Your Local Building and Electrical Codes for Guidance.