Towers | Poles | Mounts | Masts | Hardware | Guy | Cable | Wire | Carts | Racks | Tools
Your Cart
ProductQtyPrice
75 FT RG11...1$45.00
Goods Total1$45.00
View Cart Check out

Sort by:

Telescopic Mast Hardware

Adjustable 3-Way Down Guy Ring for 1-1/4" Antenna Mast

Adjustable Mount 3-Way Down Guy Ring
Price$8.95
Manufacturer Code: EZ 43-A
Qty:
Add to Cart Read More

ROHN H20 Telescopic Mast Hardware Replacement Kit

ROHN H20 Telescopic Mast Hardware Replacement Kit
Price$14.95
Manufacturer Code: H20 H Kit
Qty:
Add to Cart Read More

ROHN H30 Telescopic Mast Hardware Replacement Kit

ROHN H30 Telescopic Mast Hardware Replacement Kit
Price$22.95
Manufacturer Code: H30 H Kit
Qty:
Add to Cart Read More

ROHN H40 Telescopic Mast Hardware Replacement Kit

ROHN H40 Telescopic Mast Hardware Replacement Kit
Price$29.95
Manufacturer Code: H40 H Kit
Qty:
Add to Cart Read More

ROHN H50 Telescopic Mast Hardware Replacement Kit

ROHN H50 Telescopic Mast Hardware Replacement Kit
Price$39.95
Manufacturer Code: H50 H Kit
Qty:
Add to Cart Read More

ROHN GR1 Telescopic Mast Guy Ring 1-1/4" Rolled Edge

ROHN GR1 Telescopic Mast Guy Ring 1-1/4" Rolled Edge
Price$3.95
Manufacturer Code: GR1
Qty:
Add to Cart Read More

3 Star Adjustable 4-Way Pipe Mount HDG

3 Star Adjustable 4-Way Pipe Mount HDG
Price$13.95
Manufacturer Code: GR-2
Qty:
Add to Cart Read More

Adjustable 4-Way Down Guy Ring for 2-1/4" Antenna Mast

Adjustable 4-Way Down Guy Ring for 2-1/4" Antenna Mast
Price$13.95
Manufacturer Code: GR-2-A
Qty:
Add to Cart Read More

Remember those older AM/FM Portable Radios with the antenna that you extended by pulling it out? Or the Radio Antennas on older cars that would pop-out, extend and retract when you turned on the radio? This Mast isn't an Antenna, but it extends and retracts by hand in similar fashion. Available in 20', 30', 40' and 50' heights. All ROHN telescoping masts are pre-galvanized and come assembled with hardware. Erection is made by simply connecting guys and brackets to the attached unique heavy duty rolled edge guy rings and clamps, extend each section one at a time (starting with the innermost section), insert the locking cotter pins, rotating the tubes to a locked position, and tightening the clamps. Repeat the process on each successive section until fully erect.

The unique ROHN Products design features interior tube flanging combined with a double crimped exterior tube to produce a stronger and more stable joint than most common masts. This design exclusive also prevents the sections from accidentally pulling apart and allows disassembly by pulling each section out through the lower end.
Each section extends deeper in to the lower tubes than most other designs, adding still further to the stability of the structure.

H Series
This heavy duty series uses 1-1/4" 16 gauge galvanized tubing for top section. All other sections are 18 gauge.

Assembly
1. Secure base and anchors (sold separately).
2. Attach lowered mast to base.
3. Secure guy lines to the lower Guy Ring and attach to anchors. Align the mast vertically by tightening the Guy Lines.
4. Secure upper Guy Ring using the appropriate Mast Clamp to desired location on the upper Tube (see note 8 on page 10).
5. Secure appropriate length guy lines to the upper Guy Ring and let them hang.
6. Raise the upper Tube and inset the cotter pin. Make sure that the cotter pin is inside the notch in the inside tube.
7. Secure the cotter pin and tighten the mast clamp.
8. Secure appropriate length guy lines to the next highest Guy Ring, and let them hang.
9. Raise the next smallest Tube and insert the cotter pin. Make sure that the cotter pin is inside the notch in the inside tube.
10. Secure the cotter pin and tighten the mast clamp.
11. Repeat steps 8-10 until all sections have been raised and are secured.
12. Attach all hanging Guy Lines to their respective anchor. Align the mast vertically by tightening the Guy Lines. Make sure to work your way up the mast while tightening.