EZ NP-30-166 Non-Penetrating Low Profile Roof Dish Mount 1.66" OD x 30 inch Antenna Mast
Easy Up
Made in the USA!
The NP-30-166 is a Flat Roof Mount with a 1.66" OD x 30 inch Antenna Mast that is ideal for Light Duty Off-Air TV, Cellular, Wireless Internet, SCADA, CCTV, Telemetry, Flat Panel, Small Parabolic 2.4/5.8 GHz. MIMO Link, Specialty Omni Reception, Specialty UHF, Starlink Gen 3, Single Satellite DirecTV and DISH Network, DBS and other small Antenna mounting. It can be configured as a Non-Penetrating, Guyed or Screw-down installation on a Flat Roof or at Ground level, and comes with assembly hardware. Non-Penetrating installations typically use (6) Standard Sized (8 x 8 x 16 inch) Concrete Blocks (Not Included) as Ballast Weight placement upon the 28.5 x 35.5 inch Pre-galvanized Square Frame Base, with a Mat or Pad underneath (available separately) as to avoid roof membrane marring and penetrations.
Height and Antenna Loading capability are dependent upon ballast weight to counter the tip-over moment of the Windspeed rating desired. In addition to the Windspeed Loading Data found under the "Specification" tab (if Available), You need to Consult an Engineer to determine the Building Code Requirements and Load Bearing Capacity of the roof structure where you will be installing this mount. It is Important to choose a Mount and Mounting Location with a Picture of the Finished Installation in Mind. Be Sure to First select a location that lends itself to applying a Load without Compromising the Integrity of the Material you place the mount on top of; i.e. roof membrane, covering, decorative cover, etc., or the Structural Members beneath. Next consider the Location over a Lifetime of Adjustments, does it lend itself to modifications in Height or Direction? Larger Antennas increase the surface area presented to air movement and thus, Wind-load does increase. As the height of the mast increases from Its last attached point on the structure, the torque applied in cantilever towards the tip-over moment also increases with Antenna off-center Weight and Wind-Load EPA (Effective Projected Area), requiring a more substantive Downward Force and/or Load Dissipation; i.e. supplemental Down-guys may be required as to keep ballast weight within Load-bearing capacity. Keep the Distance Minimal from the Antenna to the Equipment you feed, as to minimize loss and the need for Amplification.
A Retention Tether SCK150 (Safety Cable Kit) is required for Commercial Installations to mitigate Loss and Damage to Property, Further, the FRM-PAD or FRM-MAT is recommended for all installations to prevent slippage, distribute weight more evenly and prevent damage to the roof surface
Tripod Antenna Mast Mounts
Tripod mounts offer fast, easy installation for one person. The legs adjust to any rafter spacing. Available in a range of sizes, tripods are shipped completely assembled with no loose parts so they can be quickly installed at your location.
Unmatched strength, durability and corrosion protection with heavy gauge,high quality, tubular steel uprights featuring the Sun-Coat process. This special triple-coating of zinc, chromate and polymer gives a smooth, shiny finish.
Eave & J Mounts For Antenna Mast Pipe
The first key to any reception is to get above obstructions that exist between you and your target, as radio frequency reception of any kind (satellite, microwave, Radio and TV) are for the most part "Line-of-Sight" dependant. The fact that some receptions occur without line of sight is due to phenomenon not applicable in this discussion. As you increase your target distance, you increase the territory you must account for in maintaining line-of-sight. What tall building and air traffic exist in this corridor, no one can account for. Aircraft are very good at messing up reception for a number of reasons, even when flying way above the path, again removed for clarity in this discussion. Height, is therefore key in optimizing your ability to capture the best line-of-sight possible to your target.
The Roof of any Building of Home provides a Logical Platform of Height in which Line-of-Sight is more likely to occur, or from which, more height can easily be obtained. These Mounts are Quality made by Manufacturers with a History in the Field of Proven Success and Longevity.
