10' Foot x 1.25" inch OD 16 AWG HDG Antenna Mast Pole Pipe Swaged | ROHN 161005GHS
ROHN
Made in the USA!
This is a 10 Foot (120") by 1.25" OD 16 AWG HDG Galvanized Swaged Antenna Mast with a notch in the receiving end as to mate with the swage of another of this same item to prevent twisting. There's a Big difference between 18 AWG and 16 AWG when it comes to joining Swaged to Straight Antenna Masts. You cannot mix and match 16 and 18 gauge masts so please, verify the mast you have before purchasing a complimenting swaged section. Be Sure and afford yourself 2 feet minimum, up to 1/3 of the overall mast length between the two wall mounts you would utilize in your TV antenna Installation. The Torque applied from wind load through cantilever to these mounts can be significant.
Manufacturers recommend that mast heights of 10 feet and higher be guyed.
(Mount Not Included)
This Item Ships LTL Freight ONLY.
Pre-Galvanized Steel Mast | Aluminum Mast Tube & Hot Dipped Galvanized Steel Pipe
3 Star Inc offers a complete line of Antenna Masts made from Pre-Galvanized Steel of 18 and 16 Gauge wall thickness of 1.00", 1.25", 1.50", 1.66" and 2.00" OD, offered in 4, 5, 8 and 10 foot lengths with both uniform and swaged fitment. They are the Mainstay of Mast poles utilized in Residential and Commercial markets from Off-Air TV, Cell repeater and Wireless Internet Gateway to IoT, Weather Instrumentation and on Property Network Links.
Read more for Addl. Product info.
Our Aluminum Mast Poles come in 1.25", 1.50" and 2.00" OD, and lengths of 6, 8, 10 and 16 feet for use on Aluminum Towers as Pinnacle Masts, Residential and Commercial Installations of Wall and Roof mount Starlink Terminals and Scada Remote Telemetry.
Manufacturers recommend that mast heights of 10 feet and higher above the uppermost bracket, mount and/or preceding guy level be guyed at the uppermost level for Additional Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance.
A Variety of Wall and Roof Mounts for these Masts are Available Here:
Antenna Mast Roof and Wall Mounts
We Stock Hot Dipped Galvanized Steel Pipe in 1-1/4", 1-7/8", 2-3/8" and 3-1/2" OD with 14 gauge and Schedule 40 wall thicknesses of 5, 7 and 10 foot lengths used on Communications Tower and Heavy Duty Wall Mounting for a variety of Cellular, PCS, Wireless Cable, Microwave, Wireless Internet, WiFi Hot Spots, DBS, MDS, MMDS and UHF/VHF Installations.
Hot Dip Galvanization provides a protective zinc coating that prevents rust and corrosion from water or moisture over time.
A Variety of Tower Antenna Mount Assemblies for this Pipe are Available Here:
Tower Antenna Mount Assemblies
A Variety of Heavy Duty Antenna Wall Mounts for this Pipe are Available Here:
Heavy Duty Antenna Wall Mounts
We will Happily answer any questions you may have on this Product Line with more detailed information, Installation and Specification Sheets covering routine Installation Scenarios as available.
Contact Us or Call Us at 877-660-0974 at anytime with any Questions you may have regarding Use prior to Purchase.
Note:
Telescopic masts are not recommended for Commercial, CB or Beam antenna installations.
Antenna load (top load ) should not exceed an effective projected area ( EPA ) of 2 square feet
(see your antenna specifications)
