ROHN 45AG Top Cap Section with 2.00" OD Mast Tube for 45G Tower
ROHN
Made in the USA!
The ROHN 45AG Top Cap Pinnacle Section is 9'-0" in height, consists of 14 gauge walls with 4 bays of bracing, swaged double-bolted connections and a 2.00" OD Mast Tube protruding 12.00 inches above apex of side rails at the Pinnacle of this Section. A 2.00 inch Outside Diameter Mast Tube at the Pinnacle of the ROHN Top Cap Section means approx. 1-13/16 inch Inside Diameter(2.00" OD/1.87" ID). Further, this Tube is affixed from the ROHN Factory with a 1.25 inch Inside Diameter Tower Mast Bushing on the Top End (ROHN indicates that it can be removed as it is only tack welded in). The bottom end of the Tube is free of attachments, but can have the ROHN TB50 (1.25 inch Inside Diameter) or TB75 (1.50 inch Inside Diameter) peened in to float in and complete your 1.25 inch Outside Diameter or 1.50 inch Outside Diameter Antenna Mast installation onto the 45AG.
Each 45G Tower Section is Hot Dip Galvanized is shipped containing all required nuts and bolts inside one leg.
This Item Ships LTL Freight ONLY!
| 45AG | |||
|---|---|---|---|
| QUANTITY | PART NUMBER | DESCRIPTION | |
| 1 | 45AG | Top Cap Tower Section - 2" O.D. | |
| 1 | 45AJBK | Bolt Kit for (45G) Top Tower Section | |
Download
ROHN 45G Tower Sections & Concrete Embed Bases
Since there are various other Manufacturers of Towers and Tower accessories that copy the ROHN Tower design, if you are not sure of the manufacturer of your Tower, you can at least compare the actual measurements and design of yours to those found in the spec. sheets in the ROHN catalog section via the Link provided above to assure yourself that additional sections or parts will fit. We cannot make that determination for you as the ROHN clones are something we don't carry or otherwise represent in our Product line. All towers in the GT Series are constructed with high strength steel tubing and feature ROHN's exclusive Zig-Zag ® solid rod bracing to provide exceptional strength. All GT Series Towers are hot dip galvanized after fabrication. In this process, each section of the tower is totally immersed in molten zinc, allowing every square inch of the tower, inside and out, to be completely covered. Hot dip galvanizing protects all points of welding and construction against rust and corrosion while providing an attractive finish.
The 45G is a true multi-use structure that provides excellent strength for applications up to 300´. It´s offered with either heavy steel tube legs to satisfy a wide variety of needs under varied conditions. When properly installed, the standard tower will support the loads shown on various guyed and self-supporting information sheets in the ROHN catalog.
Most Restrictions Allow for 45 feet of Height without the Necessity of Guy Wires, Anchors or Braces. However, No Tower is self supporting during construction! Always use temporary guys on the top most section, and install permanent guy wires as soon as a guy point height is reached.
Wind Loading, Antenna Loading and Wind Survivability ratings vs. Height Documentation Provided by ROHN is available here as a Resource, but is by no means complete by itself or a substitution for Engineering Conducted Specific to your Application. Contact Us with any Questions you may have regarding Use prior to Purchase. All Information regarding the ROHN 45G Tower line, Parts and Accessories is as accurate and complete as we can possibly provide given that this Resource Offering is subject to change without Notice and is beyond Our Control.
This Buyers Guide will answer many questions you may have on this Product Line. For more detailed information and Specification Sheets covering many aspects of Various Parts, Accessories and Installation Scenarios... Please refer to the "ROHN 45G Tower" Link appearing in the Footer of this Page Below!
Sorry, we are offline,
click here to send us message
