ROHN UM50 Telescopic Antenna Mast Roof Mount for H50 on Flat, Slope or Peak

Easy Up EZ 19B Base for Antenna Roof Mount fits 1-1/2" to 2-1/2" OD Mast Pole
Made in the USA!
This EZ19B Heavy Duty Antenna Roof Mount Base is for Installation of Telescopic or ANY Antenna Mast Pole 1.50" to 2.50" in Outside Diameter on a Flat, Pitched or Peaked Roof. This Heavy Duty Range Base is comprised of Galvanized 16 gauge steel Swivel Feet that conform to Peak or Pitched Roof contours allowing the Mast to be Raised and Lowered in place, secured with a galvanized 16 gauge 2-3/4" ID Collar and (2) Double Nut set screws.
(Mounting Hardware and Pitch Pads Not included)
Mast will require Down Guys to remain in place against wind-load.
Will Also Accommodate Telescopic Masts:
ROHN H40 H50 and Easy Up TM-40 TM-50

ROHN ETMB Roof Antenna Base Mount for Telescopic and Mast Pole up to 2-1/4" OD
Made in the USA!
This ROHN ETMB Universal Roof Antenna Mount Base is made for installing Telescopic and ANY Antenna Mast Poles up to 2.25 inch Outside Diameter on a Flat or Pitched Roof, providing your installation assures both structural and moisture barrier integrity. The Bottom of Mast inserts into the Hinged Clamp, Adjustable for Antenna Masts up to 2.25 inches in Diameter. Bonding should be made by affixment to Mast.
Will Also Accommodate Telescopic Masts:
ROHN H20 H30 H40 H50 and Easy Up TM-20 TM-30 TM-40 TM-50
Manufacturers recommend that mast heights of 10 feet and higher above the uppermost Support or Bracket be guyed for Addition Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance

Easy Up EZ 32 Base Plate for Telescopic Pole and Antenna Mast 1-1/4" to 2-1/4" OD
Made in the USA!
This Easy Up EZ32 Galvanized 9x9 inch 16 gauge Base Plate and Pier pin style Stake is for Ground Level Elevation installation of Telescopic and ANY Antenna Mast Poles from 1.25 to 2.25 inch Outside Diameter in both Temporary and Permanent Base Mounting by placement upon a Gravel or Concrete Foundation with the Center Stake inserted into, and the Plate resting on top of, a (1) Foot Cubed bed of gravel or pad of Poured Concrete above surrounding soil elevation.(depending on soil and frost conditions) The Pier Pin Style Center Stake Rod is approximately 1" in OD and floats freely within the Mast Tube placed over it and is not fixated other than by the Down Guys installed to secure the mast from wind-load.
Will Also Accommodate Telescopic Masts:
ROHN H20 H30 H40 H50 and Easy Up TM-20 TM-30 TM-40 TM-50
Manufacturers recommend that masts heights of 10 feet and higher above the uppermost bracket be guyed for Addition Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance

Easy Up EZ 32A Base Plate with 3" Mast Collar for Telescopic Pole and Antenna Mast 1-1/2" to 2-1/4" OD
Made in the USA!
This Easy Up EZ32A Galvanized 9x9 inch 16 gauge Base Plate comes with a welded on 3 inch tall by 2.25" ID Mast Collar with single bolt Set Screw and a separate Pier Pin style Stake for Ground Level Elevation installation of Telescopic and ANY Antenna Mast Poles from 1.50 to 2.25 inch Outside Diameter in both Temporary and Permanent Base Mounting by placement upon a Gravel or Concrete Foundation with the Center Stake inserted into, and the Plate resting on top of, a (1) Foot Cubed bed of gravel or pad of Poured Concrete above surrounding soil elevation.(depending on soil and frost conditions)
Will Also Accommodate Telescopic Masts:
ROHN H20 H30 H40 H50 and Easy Up TM-20 TM-30 TM-40 TM-50
Manufacturers recommend that masts heights of 10 feet and higher above the uppermost bracket be guyed for Addition Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance