3-Way Down Guy Wire Kit for 30 Foot Telescopic Antenna Mast H303WAYGUY
3 Star Inc
This H303WAYGUY Kit is a 3-way Down Guy Wire and Anchor package to secure your ROHN H30 and Easy Up TM30 Telescopic Push Up Antenna Masts at 3 levels. Guy wire gauge, Anchor size and Base Mount are Selectable Options.
(Mast is not included)
Works with the following Telescopic Masts:
ROHN- H30
Easy Up- EZ TM-30, EZ TM-30-U-95
Channel Master- 1630, 1830
| BILL OF MATERIALS: 30 Foot 3-Way Guy Wire & Anchor Kit | ||
|---|---|---|
| QUANTITY | PART NUMBER | DESCRIPTION |
| DOWN GUY WIRE SELECTION | ||
| 400 FT | (Includes) EZ 60 A | 6 Strand 20 Gauge Guy Wire |
| 400 FT | (Optional) EZ 60 | 6 Strand 20 Gauge Guy Wire Plastic Coated |
| 400 FT | (Optional) 618 | 6 Strand 18 Gauge Guy Wire |
| DOWN GUY ANCHOR SELECTION | ||
| 3 | (Includes) EZ 30 | 30” by 1/2” DIA Screw Anchor w/ 3” Helix |
| 3 | (Optional) EZ 48 | 48” by 5/8” DIA Screw Anchor w/ 6” Helix |
| CLAMPS/GRIPPLES INCLUDED | ||
| 9 | (Includes) 61820GRPL | Gripple for 20 and 18 Gauge Guy Wire used for Termination and Tension Adjustment of Guy Wire |
| 27 | (Includes) 1/8CCF | 1/8” Hot-Dipped Galvanized Cable Clamp |
| BASE PLATE MOUNT SELECTION | ||
| 1 | (Includes) EZ 32 | Standard Baseplate 9" Sq. Plate/No Collar Pier Pin Included |
| 1 | (Optional) EZ 32C | Heavy-Duty Baseplate 9” Sq. Plate/ 6" Collar -w- (1) Set Screw Accepts 2.25" OD Mast Pipe Pier Pin Included |
| 1 | (Optional) EZ TS-50 | Heavy-Duty Direct Ground Mount 9” Sq. Plate/18" Collar -w- (2) Set Screws Accepts 2.25" OD Mast Pipe 18.75" Welded Drive-in Rod (Stake) For Temporary Installations |
| TELESCOPIC MAST SELECTION | ||
| 1 | (Optional) EZ TM-30-U-95 | UPS Shippable Telescopic Mast Extends to 21.5 Feet ONLY |
General Information
This 3-Way Guy Wire and Anchor Kit is for 30 Foot Telescopic Push Up Antenna Masts.
Includes the accessories needed to SECURELY affix a Ground Based Telescopic Mast at the (3) levels of Down Guys from Guy Rings.
(Guy Rings supplied on Your Mast)
The standard Baseplate given is solely used for GROUND Mounted Installations.
There are other Mounts Designed for Roof Installations.
Wall Brackets may add to Structural integrity but do Not Replace the need for Down Guys.
Manufacturers recommend that masts heights of 10 feet and higher above the uppermost bracket be guyed for Addition Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance
PLEASE CONTACT A STRUCTURAL ENGINEER or PROFESSIONAL before installing Premise attached Structure.
As with all masts, Guy Wire Support and Grounding are CRITICAL to Antenna Survival.
Reference the Telescopic Mast ROHN Buyer’s Guide by Height to build or supplement your Telescopic Antenna Mast installation by clicking the Specification or More Info Tab above.
3-Way Down Guy Wire Kits are typically used for Ground-Based installations.
4-Way Down Guy Kits are typically used for Roof-Based installations.
Installations that are combination or hybrid and utilize substitution or additional structural components should be forwarded to and engaged by an Engineer qualified to make such decisions.
Download
Telescoping Antenna Mast Down Guy Kits
Remember those older AM/FM Portable Radios with the antenna that you extended by pulling it out? Or the Radio Antennas on older cars that would pop- out, extend and retract when you turned on the radio? This Mast isn't an Antenna, but it extends and retracts by hand in similar fashion. Available in 20', 30', 40' and 50' heights. All ROHN telescoping masts are pre-galvanized and come assembled with hardware. Erection is made by simply connecting guys and brackets to the attached unique heavy duty rolled edge guy rings and clamps, extend each section one at a time (starting with the innermost section), insert the locking cotter pins, rotating the tubes to a locked position, and tightening the clamps. Repeat the process on each successive section until fully erect.
The unique ROHN Products design features interior tube flanging combined with a double crimped exterior tube to produce a stronger and more stable joint than most common masts. This design exclusive also prevents the sections from accidentally pulling apart and allows disassembly by pulling each section out through the lower end.
Each section extends deeper in to the lower tubes than most other designs, adding still further to the stability of the structure.
H Series
This heavy duty series uses 1-1/4" 16 gauge galvanized tubing for top section. All other sections are 18 gauge.
Assembly
1. Secure base and anchors (sold separately).
2. Attach lowered mast to base.
3. Secure guy lines to the lower Guy Ring and attach to anchors. Align the mast vertically by tightening the Guy Lines.
4. Secure upper Guy Ring using the appropriate Mast Clamp to desired location on the upper Tube (see note 8 on page 10).
5. Secure appropriate length guy lines to the upper Guy Ring and let them hang.
6. Raise the upper Tube and inset the cotter pin. Make sure that the cotter pin is inside the notch in the inside tube.
7. Secure the cotter pin and tighten the mast clamp.
8. Secure appropriate length guy lines to the next highest Guy Ring, and let them hang.
9. Raise the next smallest Tube and insert the cotter pin. Make sure that the cotter pin is inside the notch in the inside tube.
10. Secure the cotter pin and tighten the mast clamp.
11. Repeat steps 8-10 until all sections have been raised and are secured.
12. Attach all hanging Guy Lines to their respective anchor. Align the mast vertically by tightening the Guy Lines. Make sure to work your way up the mast while tightening.
This Buyers Guide has will answer many questions you may have on this Product Line. For more detailed information and Specification Sheets covering many aspects of Various Parts, Accessories and Installation Scenarios. Please refer to the "Telescopic Mast" Link appearing in the Footer of this Page Below!
Telescoping Masts are not recommended for commercial, CB or beam antenna installations.
Sorry, we are offline,
click here to send us message
