618 Down Guy Wire for Telescopic Antenna Mast Installations 1000' feet

3 Star Inc 618-50 618 Down Guy Wire in 50 ft Hanks up to 1000' for Antenna Mast Pole
50 foot segment of 6 Strand, 18 AWG Steel Antenna Mast Down Guy Wire for Light, Medium and some Heavy Duty Antenna Mast Guying installations. Comes as 50 foot Hank section for each order with multiple quantities ordered coming in continuous footage up to 1000 feet.

3 Star Inc EZ 60 620 Plastic Coated Down Guy Wire 1000' ft for Antenna Mast Pole
Comes as linked 50 foot hank segments of Plastic Coated 6 Strand, 20 AWG Steel Down Guy Wire for Guying Light to Medium Duty Antenna Mast and Telescopic Poles. Each Order is for Twenty 50 foot Hank Sections in continuous footage totaling 1000 feet.

3 Star Inc EZ 60A 620 Down Guy Wire in Contiguous 1000' ft for Antenna Mast Pole
Comes as linked 50 foot hank segments of 6 Strand, 20 AWG Steel Down Guy Wire for Guying Light to Medium Duty Antenna Mast and Telescopic Poles. Each Order is for Twenty 50 foot Hank Sections in continuous footage totaling 1000 feet.

3 Star Inc 3/8X6TBE&J Turnbuckle for Tower Down Guy 3/8" x 6" Eye to Jaw
Federal Spec FF-T-791B Type 1 Form 1; Forged, Hot Dip Galvanized, Open Body, Working Load Limit: 1200 lbs. Ultimate Strength: 6000 lbs. The Turnbuckle eye is elongated to reduce stress on eye and make it easier for Thimbles and other hardware to pass through.

3 Star Inc EZ48 48" inch Screw Anchor for Telescopic Antenna Mast Down Guy
Made in the USA!
This 48" long Screw-in Earth Anchor with 5/8" Rod and a 6" Helix is Hot Dip Galvanized (HDG) for attaching down guy wire when Guying ROHN H20, H30, H40, H50 and Easy Up TM20, TM30, TM40, TM50 Telescopic Antenna Masts.

3 Star Inc EZ 62A 1" Slit Corrugated Loom Tubing Cable and Down Guy Wire Cover
Made in the USA!
This is Corrugated Loom Tubing Slit, 1" (25.4mm) x 7 feet, Yellow UV resistant for applications where Spiral Wrap or Braided Expandable Sleeving may be difficult to install over the guy wire as a guard or they do not offer the amount of protection required. This can also be used in conduit applications to protect individual or grouped wires and cables when routed to their destination connection.

Easy Up EZ 19B Base for Antenna Roof Mount fits 1-1/2" to 2-1/2" OD Mast Pole
Made in the USA!
This EZ19B Heavy Duty Antenna Roof Mount Base is for Installation of Telescopic or ANY Antenna Mast Pole 1.50" to 2.50" in Outside Diameter on a Flat, Pitched or Peaked Roof. This Heavy Duty Range Base is comprised of Galvanized 16 gauge steel Swivel Feet that conform to Peak or Pitched Roof contours allowing the Mast to be Raised and Lowered in place, secured with a galvanized 16 gauge 2-3/4" ID Collar and (2) Double Nut set screws.
(Mounting Hardware and Pitch Pads Not included)
Mast will require Down Guys to remain in place against wind-load.
Will Also Accommodate Telescopic Masts:
ROHN H40 H50 and Easy Up TM-40 TM-50

Easy Up EZ 32C Base Plate with 6" Mast Collar for Telescopic Pole and Antenna Mast 1-1/2" to 2-1/4" OD
Made in the USA!
This Easy Up EZ32C Galvanized 9x9 inch 16 gauge Base Plate comes with a welded on 6 inch tall by 2.25" ID Mast Collar with single bolt Set Screw and a separate Pier Pin style Stake for Ground Level Elevation installation of Telescopic and ANY Antenna Mast Poles from 1.50 to 2.25 inch Outside Diameter in both Temporary and Permanent Base Mounting by placement upon a Gravel or Concrete Foundation with the Center Stake inserted into, and the Plate resting on top of, a (1) Foot Cubed bed of gravel or pad of Poured Concrete above surrounding soil elevation.(depending on soil and frost conditions)
Will Also Accommodate Telescopic Masts:
ROHN H20 H30 H40 H50 and Easy Up TM-20 TM-30 TM-40 TM-50
Manufacturers recommend that masts heights of 10 feet and higher above the uppermost bracket be guyed for Addition Wind Load Support. Bonding/Grounding should be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance