VMP FRM-200 Powder Coat Non-Pen Wifi or Satellite 2.00-2.38 OD Option Mast
VMP
is constructed of steel and uses standard concrete blocks for Ballast on Flat Roof. Mast is 2.00 inches in Outside Diameter and 30 inches in Height from Base. For use with DBS, TV Antenna and Satellite Internet systems. Can be Used as a Penetrating Mount without Ballast.
This Non-Penetrating Mount Series from VMP is finished with a dark brown weather resistant powder coat inside and out that blends well with residential environments. The 2.00 inch Diameter Pipe size mounts AU9S Dish, DirecTV 5 LNB Dish AU9 Slimline, WildBlue, SuperDISH, DirecTV Ka/Ku (HD Dishes), Satellite Dishes compatible with the SUPERDMOUNT, DirecTV AT9, DBS Direct Broadcast Satellite and FTA Free to Air using a 2.00 inch OD Outside Diameter Mounting Pipe. In addition, it can be used in mounting some smaller Microwave PCS, Cellular, Broadband Wireless, Wireless Internet and Two Way Antennas compatible with 2 inch O.D. Pipe Mounting. I have enjoyed Installing this product line for Dish applications from Business and Internet on the tops of tall buildings to HD TV and zillions of channels for in-home use. And as with all items in this Product Line, Screws and Pitch Pads are included for Bolt-down versus Ballast applications. The Length of the mast is 30 inches based on engineering that incorporates consideration for typical Satellite Antenna Wind-load versus the Ballast that would keep either on target with minimal deviation and flex. As with all Ballast mounts, Structural Engineering consultations are recommended for all Roof Applications.
FRMA OPTION-(see above) Converts the 2.00 inch OD mast pipe to a 2.375 inch OD Mast Pipe Diameter ideal for HughesNet, DirecWAY, StarBand Satellite Dish and Microwave Antenna Mounting. A VMP Product that is constructed of steel, Powder-coated to match the VMP Non-Penetrating Flat Roof Mount Product Line. Compares to Other Name Brand Hardware at Half the Price.
Height and Antenna Loading capability are dependent upon ballast weight to counter the tip-over moment of the Windspeed rating desired. In addition to the Windspeed Loading Data found under the "Specification" tab (if Available), You need to Consult an Engineer to determine the Building Code Requirements and Load Bearing Capacity of the roof structure where you will be installing this mount. It is Important to choose a Mount and Mounting Location with a Picture of the Finished Installation in Mind. Be Sure to First select a location that lends itself to applying a Load without Compromising the Integrity of the Material you place the mount on top of; i.e. roof membrane, covering, decorative cover, etc., or the Structural Members beneath. Next consider the Location over a Lifetime of Adjustments, does it lend itself to modifications in Height or Direction? Larger Antennas increase the surface area presented to air movement and thus, Wind-load does increase. As the height of the mast increases from Its last attached point on the structure, the torque applied in cantilever towards the tip-over moment also increases with Antenna off-center Weight and Wind-Load EPA (Effective Projected Area), requiring a more substantive Downward Force and/or Load Dissipation; i.e. supplemental Down-guys may be required as to keep ballast weight within Load-bearing capacity. Keep the Distance Minimal from the Antenna to the Equipment you feed, as to minimize loss and the need for Amplification.
A Retention Tether SCK150 (Safety Cable Kit) is required for Commercial Installations to mitigate Loss and Damage to Property, Further, the FRM-PAD or FRM-MAT is recommended for all installations to prevent slippage, distribute weight more evenly and prevent damage to the roof surface
Flat Roof Non-Penetrating Mounts
These mounts can be used where penetrating its attachment is not an option. Non penetrating mounts use ballast weight like your usual cement cinder block as a method to hold down your masting structure. They can help meet the variety of communication tower needs such as Cellular, PCS, Wireless Cable, Microwave, Wireless Internet, WiFi Hot Spots, DBS, MDS, MMDS and UHF/VHF reception.
Designed and engineered to handle the job of getting above ground interference, each non-penetrating roof mount has been researched and developed to serve a specific purpose.
With professionally engineered construction, you can be assured you're getting a virtually maintenance-free product built to the highest standards. And because our non-penetrating roof mounts are hot-dip galvanized after fabrication, our mounts won't rust.
- Additional Features Include
- Offer both Fixed Mounts and Ballast Roof Mounts
- Pre-Galvanized for corrosion protection
- Varied mast heights available
- Varied mast pipe O.D. available
- Quickly shipped and quickly assembled
- Minimum bolted connections
- Engineering ballast tables available
- Optional roof pads and mats available
- All models are UPS shippable
