EZ NP-225 Non-Pen Roof Mount FRM Frame for up to 2.25 inch OD Antenna Mast
Easy Up
Made in the USA!
The EZ NP-225 is a Flat Roof Mount Frame-Only Option that allows you to supply and support your own Antenna Mast from 1.50 to 2.25 inches in Outside Diameter and from 30 to 60 inches (5 ft.) in height for Light Off-Air TV, Wireless Internet, Cellular Gateway Small MIMO, Starlink Gen 3 (2.10" OD. x 30" Height MAX) and SCADA Telemetry and Small Diameter Narrow Beam-width Antenna placement. It can be configured as a Non-Penetrating, Guyed or Screw-down installation on a Flat Roof or at Ground level, and comes with assembly hardware. Non-Penetrating installations typically use (6) Standard Sized (8 x 8 x 16 inch) Concrete Blocks (Not Included) as Ballast Weight placement upon the 28.5 x 35.5 inch Pre-galvanized Rectangular Frame Base, with a Mat or Pad underneath (available separately) as to avoid roof membrane marring and penetrations.
The Frame comes with ALL Assembly Hardware Minus the mast that You supply. Your Mast will have to be drilled at the bottom to pass a 1/4-20 bolt (included) that will secure it to the Frame Base.
Height and Antenna Loading capability are dependent upon ballast weight to counter the tip-over moment of the Windspeed rating desired. In addition to the Windspeed Loading Data found under the "Specification" tab (if Available), You need to Consult an Engineer to determine the Building Code Requirements and Load Bearing Capacity of the roof structure where you will be installing this mount. It is Important to choose a Mount and Mounting Location with a Picture of the Finished Installation in Mind. Be Sure to First select a location that lends itself to applying a Load without Compromising the Integrity of the Material you place the mount on top of; i.e. roof membrane, covering, decorative cover, etc., or the Structural Members beneath. Next consider the Location over a Lifetime of Adjustments, does it lend itself to modifications in Height or Direction? Larger Antennas increase the surface area presented to air movement and thus, Wind-load does increase. As the height of the mast increases from Its last attached point on the structure, the torque applied in cantilever towards the tip-over moment also increases with Antenna off-center Weight and Wind-Load EPA (Effective Projected Area), requiring a more substantive Downward Force and/or Load Dissipation; i.e. supplemental Down-guys may be required as to keep ballast weight within Load-bearing capacity. Keep the Distance Minimal from the Antenna to the Equipment you feed, as to minimize loss and the need for Amplification.
A Retention Tether SCK150 (Safety Cable Kit) is required for Commercial Installations to mitigate Loss and Damage to Property, Further, the FRM-PAD or FRM-MAT is recommended for all installations to prevent slippage, distribute weight more evenly and prevent damage to the roof surface
Download
Flat Roof Non-Penetrating Mounts
These mounts can be used where penetrating its attachment is not an option. Non penetrating mounts use ballast weight like your usual cement cinder block as a method to hold down your masting structure. They can help meet the variety of communication tower needs such as Cellular, PCS, Wireless Cable, Microwave, Wireless Internet, WiFi Hot Spots, DBS, MDS, MMDS and UHF/VHF reception.
Designed and engineered to handle the job of getting above ground interference, each non-penetrating roof mount has been researched and developed to serve a specific purpose.
With professionally engineered construction, you can be assured you're getting a virtually maintenance-free product built to the highest standards. And because our non-penetrating roof mounts are hot-dip galvanized after fabrication, our mounts won't rust.
- Additional Features Include
- Offer both Fixed Mounts and Ballast Roof Mounts
- Pre-Galvanized for corrosion protection
- Varied mast heights available
- Varied mast pipe O.D. available
- Quickly shipped and quickly assembled
- Minimum bolted connections
- Engineering ballast tables available
- Optional roof pads and mats available
- All models are UPS shippable
